Denon AVR-1082 manual Mono Stereo

Page 42
SPECIFICATIONS
17
ENGLISH

2 Audio section

• Power amplifier

Rated output:

Front:

105

W + 105 W

(8 Ω

/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)

 

 

150

W + 150 W

(6 Ω

/ohms, 1 kHz with 0.7% T.H.D.)

 

Center:

105

W

(8 Ω

/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)

 

 

150

W

(6 Ω

/ohms, 1 kHz with 0.7% T.H.D.)

 

Surround:

105

W + 105 W

(8 Ω

/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)

 

 

150

W + 150 W

(6 Ω

/ohms, 1 kHz with 0.7% T.H.D.)

 

Surround back:

105

W + 105 W

(8 Ω

/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)

 

 

150

W + 150 W

(6 Ω

/ohms, 1 kHz with 0.7% T.H.D.)

Dynamic power:

140 W x 2 ch

(8 Ω

/ohms)

 

 

 

210 W x 2 ch

(4 Ω

/ohms)

 

 

 

240 W x 2 ch

(2 Ω

/ohms)

 

 

Output terminals:

Front, Center, Surr. Back/Multi Zone:

6 ~ 16 Ω

/ohms

 

Surround:

A or B

6 ~ 16 Ω

/ohms

• Analog

 

A + B

8 ~ 16 Ω

/ohms

200 mV /

47 kΩ /kohms

 

 

Input sensitivity / input impedance:

 

 

Frequency response:

10 Hz ~ 100 kHz: +0, –3 dB (DIRECT mode)

 

S/N:

102 dB (DIRECT mode)

 

 

Distortion:

0.005% (20 Hz ~ 20 kHz) (DIRECT mode)

 

Rated output:

1.2 V

 

 

 

• Digital

Rated output — 2 V (at 0 dB playback)

 

D/A output:

 

 

Total harmonic distortion — 0.008% (1 kHz, at 0 dB)

 

S/N ratio

— 102 dB

 

 

 

Dynamic range — 96 dB

 

 

Digital input:

Format — Digital audio interface

 

 

•Phono equalizer (PHONO input — REC OUT)

Input sensitivity:

2.5 mV

RIAA deviation:

±1 dB (20 Hz to 20 kHz)

Signal-to-noise ratio:

74 dB (A weighting, with 5 mV input)

Rated output / Maximum output:

150 mV / 8 V

Distortion factor:

0.03% (1 kHz, 3 V)

2Video section

•Standard video jacks

Input / output level and impedance: 1 Vp-p, 75 Ω /ohms

Frequency response:

5 Hz ~ 10 MHz — +0, –3 dB

•S-video jacks

Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω /ohms

 

C (color) signal — 0.286 Vp-p, 75 Ω /ohms

Frequency response:

5 Hz ~ 10 MHz — +0, –3 dB

•Color component video terminal

Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω /ohms

 

 

PB/CB (blue) signal

— 0.7 Vp-p, 75 Ω /ohms

 

 

 

PR/CR (red) signal

— 0.7Vp-p, 75 Ω /ohms

 

 

Frequency response:

5 Hz ~ 27 MHz — +0, –3 dB

 

2

Tuner section

[FM] (note: µV at 75 Ω /ohms, 0 dBf=1 x 10–15W)

[AM]

 

 

 

Reseiving Range:

87.50 MHz ~ 108.00 MHz

522 kHz ~ 1611 kHz

 

Usable Sensitivity:

1.0 µV (11.2 dBf)

 

18 µV

 

50 dB Quieting Sensitivity:

MONO

1.6 µV (15.3 dBf)

 

 

 

STEREO

23 µV (38.5 dBf)

 

 

S/N (IHF-A):

MONO

80 dB

 

 

 

STEREO

75 dB

 

 

Total Harmonic Distortion (at 1 kHz):

MONO

0.4%

 

 

 

STEREO

0.5%

 

2

General

AC 230 V, 50 Hz

 

 

 

Power supply:

 

 

 

Power consumption:

400 W

 

 

 

 

 

2 W (Standby)

 

 

 

 

Maximum external dimensions:

434 (W) x 171 (H) x 416 (D) mm

 

 

Mass:

16.5 kg

 

 

 

2Remote control unit (RC-884)

Batteries:

R6P/AA Type (three batteries)

External dimensions:

61 (W) x 230 (H) x 34 (D) mm

Mass:

200 g (not including batteries)

* For purposes of improvement, specifications and design are subject to change without notice.

42

Page 41 Page 42
Image 42
Page 41 Page 42
Contents
~ Seite For English ReadersFÜR Deutsche Leser Seite Pour LES Lecteurs FrancaisQuesto Prodotto E’ Conforme AL D.M /08/95 NBefore Using EnglishFeatures Connecting the audio componentsConnections Connecting video components Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting the antenna terminals AM loop antenna assembly FM antenna adopter assemblyConnecting the speaker cords Connecting the external input EXT. in jacksConnecting the Multi Zone jacks Speaker system connectionsConnections Part Names and FunctionsFront Panel Surround Speaker A/BSystem Setup button Setting UP the SystemRemote control unit Cursor buttonsSetting the type of speakers Before setting up the systemSetting the power amplifier assignment Speaker system layout Basic system layoutSetting the Crossover Frequency and Subwoofer mode ParametersSetting the delay time Setting the SB CH Auto Flag DetectSetting the channel level Setting the Digital In Assignment Setting the on-screen display OSD Setting the multi vol. levelAuto tuner preset DB, -40 dBUsing the remote control unit Remote Control UnitAfter completing system setup On-screen display signalsPreset memory Operating Denon audio componentsSystem buttons Checking the preset memory settingsOperating a component stored in the preset memory ButtonsSystem call Storing system call signalsLearning function System call buttonsResetting Resetting learned buttons All reset functionEnter Before operating OperationAuto search function ¢ON/STANDBYPlaying the input source Adjusting the sound quality Tone Listening over headphonesTurning the sound off temporarily Muting Multi-source recording/playback Playing one source while recording another REC OUT modeSet the recording mode SourceMulti-source and multi-zone playback Before playing with the surround function Dolby Surround Pro Logic II modeSurround Fader functionPanorama Control Surround parameters q Pro Logic II ModeDimension Control Center Width ControlCOMP. Dynamic Range Compression Afdm Auto Flag Detect ModeSurround parameters w Cinema EQ. Cinema Equalizer LFE Low Frequency EffectDSP surround simulation Surround modes and their featuresDSP Surround Simulation Personal Memory PlusTone control setting Bass 1TREBLESurround parameters e CinemaMusic Checking the preset stations Auto tuningManual tuning Listening to the RadioRecalling preset stations RDS searchRDS Radio Data System RT Radio Text PTY searchTP search TP SearchTroubleshooting Last Function MemoryInitialization of the Microprocessor Additional Information Optimum surround sound for different sourcesSurround back speakers Speaker setting examples When using different surround speakers for movies and music When not using surround back speakers Dolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Pro LogicDTS Digital Surround DTS-ES Extended Surround TMSurround modes and parameters Mono StereoMono Stereo
Top Page Image Contents