Roper 4347928 (333240-1) manual Cooktop Knobs will not Turn, AN Element does not Work

Page 32

IF YOU HAVE A PROBLEM

COOKTOP KNOBS WILL NOT TURN

0To turn from Off position, push the knob in and then turn.

AN ELEMENT DOES NOT WORK

0 Fuse blown or circuit breaker tripped. Power outage - check by trying household lights.

0Check to be sure the individual element and/or module is plugged in firmly. See the following pages:

Open Coil or Solid Element Module - Page 9

Grill/Griddle Element - Page 13

;&G;R GRIDDLE DOES NOT GET HOT

0 The grill/griddle element is not plugged into the well receptacle firmly and is not making complete contact. See pages 13 and 17.

0 When griddling use a LO blower setting.

EXCESSIVE SMOKE, OR VENT SYSTEM IS NOT CAPTURING THE SMOKE

0The vent fan is not turned on (when using front controlsI.

0 Too much cross ventilation in the room draws smoke away from the cooktop before the vent system can eliminate it.

0The grill was not cleaned properly the last time it

was used and accumulated grease is causing ex- cessive smoke. See page 14 on cleaning the grill module.

0Excessive smoke is being created because excess fat was not trimmed from the meat and is dripping on the grill element. See page 13.

0 The grease filter is not clean.

FOOD STICKS TO THE GRILL OR GRIDDLE

0The grill or griddle was not preconditioned before the first use. See page 13 or 17.

0 Food is being cooked on too high a heat setting.

0The non-stick coating has been damaged with sharp utensils or the use of abrasive cleaners.

0Leaving the griddle on HI setting for more than 10 minutes without food can damage the non-stick coating and cause sticking.

0The grill grid or griddle was not greased before cooking.

THERE IS GREASE BELOW THE RANGE

0 The grease jar is full and has overflowed. You should check the jar each time you use the grill or griddle and empty or replace it often. See page 8.

FOOD GETS BURNED OR TOO WELL DONE ON THE GRILL OR ROTISSERIE

0Excessive fat should be trimmed from the edges of meat. As the food cooks, fat melts and drips on the element causing little bursts of flame. Ex- cessive flame-up causes food to burn or get too well done.

0Salting food while it is cooking draws natural juices out of the food and tends to dry the food.

0Always use tongs to handle or turn food on the grill. Piercing food with a fork causes juices to be lost and dries the food.

COOKING RESULTS ARE NOT WHAT YOU EXPECTED

0See the cooking charts in each section of this

manual for general guidelines. Remember, you may need to make cooking time and/or heat set-

ting adjustments for the food you are cooking.

Food temperature, thickness and moisture con- tent all affect cooking time and heat settings.

30

Page 31 Page 33
Image 32
Page 31 Page 33
Contents AL-I Read and Save this BookThispage Intentionallyleftblank Using Oven Cleaning CareMaintenance Model NO. Serial no Date PurchasedGeneral Protect Your ChildrenSafe ,TY Grease Fires Ventilating Fans SELF-CLEANING OvenPutting OUT a Grease Fire Important Information Using Cooktop Controls Recipes Cooktop Signal LightUsing Open Coil Elements Using Downdraft VentingCleaning Downdraft Vents Grease JarsUsing Electric Elements dlrB’ Inserting a Module @Cleaning the Modules Removing a Module #DEnergy Saving Tips Choosing Cooktop CookwareCookware Chart Control Setting GuideUsing the Grill Inserting the Grill ModuleCleaning the Grill Module Grilling TipsRemoving the Grill Module Module CoverChart Page Using the Griddle Cleaning the GriddleInserting the Griddle Module Removing the Griddle ModuleGriddle Chart Salt Rotissing Tips Using the RotisserieAssembling the Rotiswkebab Module Cleaning the Rotiswkebab Module Shish Kebabing TipsUsing the Oven Oven LightUsing Foil PreheatingBroiling Tips Positioning Broiler PANOven Using a Meat ThermometerRackandpanarrangement Common Before a Clean Cycle Important InformationTo SET a Clean Cycle To Stop a Clean CycleWhen a Clean Cycle is Finished After a Clean CycleRemovable Oven Door Removable Oven RacksReplacing the Oven Light Cooktop Knobs will not Turn AN Element does not WorkGR Griddle does not GET HOT Excessive SMOKE, or Vent System is not Capturing the SmokeCLOCK/TIMER does not Work Broiling ProblemsOven will not SELF-CLEAN Oven Door will not Unlock After SELF-CLEANING CycleModules and Accessories Limited Warranty

4347928 (333240-1) specifications

The Roper 4347928 (333240-1) is an advanced mechanical component designed for various industrial applications, showcasing a blend of robust materials, precise engineering, and cutting-edge technology. This product is recognized for its reliability and efficiency, making it a preferred choice among professionals in multiple fields.

One of the standout features of the Roper 4347928 is its durable construction. Made from high-quality materials, this component is capable of withstanding harsh operating conditions, including extreme temperatures and corrosive environments. This durability ensures long-term performance and minimizes the need for frequent replacements, ultimately leading to cost savings.

The Roper 4347928 also boasts a compact design, which is essential for applications where space is limited. Its small footprint allows for easy integration into existing systems, making it a versatile solution for various machinery and equipment. This adaptability is further enhanced by its compatibility with different models, ensuring seamless installation and operation.

In terms of technology, the Roper 4347928 incorporates advanced engineering principles that contribute to its high performance. The component features precision machining that enhances its operational efficiency, reducing friction and wear during use. This not only improves the lifespan of the component but also ensures a smoother operation, which is critical in maintaining overall system reliability.

Another characteristic that sets the Roper 4347928 apart is its ease of maintenance. The design includes accessible points for lubrication and inspection, allowing users to perform regular checks with minimal effort. This user-friendly aspect is vital for industries where downtime can result in substantial losses, as it enables quicker service and less interruption in operations.

Moreover, the Roper 4347928 is subject to rigorous quality control measures during the manufacturing process. Each unit undergoes thorough testing to ensure it meets industry standards for performance and safety. This commitment to quality guarantees that users receive a product they can trust for their critical applications.

In conclusion, the Roper 4347928 (333240-1) represents a well-engineered solution characterized by its durability, compact design, advanced technology, ease of maintenance, and adherence to quality standards. Whether used in manufacturing, automotive, or various other sectors, this component delivers exceptional performance and reliability, making it a valuable asset in any industrial setting.
Top Page Image Contents