EXCESSIVEWEIGHTHAZARD
Usetheassistanceoftwoormorepersonstomoveor installtherefrigeratorNotfollowingtheseinstructions maycauseinjuryto thebackandotherpartsof the body
UNPACKING Beforeinstallingyourrefrigerator,removeanytape or temporarystickersDo not removeanystickers thatfeaturewarnings,themodelserialnumberorthe technicallabeloftheproductlocatedonthebackofthe refrigerator
To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent Clean with warm water and let dry
Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the adhesive tape or glue These products can damage the
surface of your refrigerator For more information, see
the section on "important Safety Instructions"
The shelves come already installed in their factory
position Remove the shelves and replace them
3.Installtherefrigeratorinanareabetween55°F
(13°C)and110°F(43°C)Ifthesurroundingtemperature isloweror higherthanpreviouslymentioned,it can adverselyaffecttheunit
CAUTION:Avoidplacingthe unit nearheat sources,directsunlightorhumidity
ONCE INSTALLED
1.Carefully clean your refrigerator and remove and dust
accumulated during shipping
2.Install accessories such as the ice bin, door racks, shelves, etc, in their proper places These are already
packed to prevent any possible damage during shipping
3.Leave your refrigerator on for 2 to 3 hours before storing food inside Verify that there is a flow of cold air
in the freezer compartment to ensure proper cooling Your refrigerator is now ready for use
WARNING:
oTake care when working with the hinges, base cover and stops, etc You may injure yourself
•DO not place your hands or any tools in the air vents,
the base cover or in the bottom of the refrigerator This
may cause injury or electrical shock
according to your spacing needs
_Moving Your Refrigerator:
Your refrigerator is extremely heavy Make sureyouJ protect the floor when moving your refrigerator for/
cleaning or servicing Always pull your refrigerator / straight out when moving it Do not shift from side /
to side or "walk" the refrigerator when attempting to I
INSTALLATION | OF BASE | GRILLE |
| ||||
Uninstalling | or | Replacing | the | Base | Grille |
| |
1. Remove | the | 2 screws | from | the | bottom | front part of | |
your | refrigerator | (see | Figure | A) |
|
| |
2.Take | off | the | cover |
|
|
|
|
move it as this can cause damage to the floor | S |
Figure A
EXPLOSION HAZARD
Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator Not following
these instructions may cause death, explosion or fire
INSTALLATION
1. Avoid | placing | the | unit | near | heat |
| sources, | direct | ||||||
sunlight, | or | humidity |
|
|
|
|
|
|
|
|
|
| ||
avoid | vibration, |
| the | unit | should | be | leveled | If needed, | ||||||
adjust | the | leveling |
| screws | to | compensate |
| for | an | |||||
unleveled | floor | The | front | should | be | slightly | taller |
| than | |||||
the | rear | to | ensure | that the | doors | close | properly |
| The | |||||
leveling | screws | can | easily | be turned | by slightly | tilting | ||||||||
the | front | of | the | refrigerator, |
| turning | the | leveling | screws | |||||
clockwise | ( | ,,mL._ | ) | to | raise | it | and |
|
| |||||
( _mL. ) | to | lower | it |
|
|
|
|
|
|
|
|
|
| |
Installing the Base Grille
1. Align the bottom cover and place in position Insert
the 2 screws and twist in place (see Figure B)
Figure B
Keep a Proper Distance from Adjacent
Objects
Please keep the refrigerator at an
adequate distance from other objects
Insufficient spacing can reduce the
refrigerator's freezing efficiency and
increase electricity consumption
_0_