Liebherr 120309 7084442 - 00 Putting into operation, Insertion into a row of kitchen units

Putting into operation

uTip the appliance back a little again and re-insert the bear- ing pin Fig. 6 (22). The notch has to point forwards.

uPlace the cover Fig.5 (27) on the opposite side.*

Fig. 6

CAUTION

Risk of injury if the door tips!

u The safety lock (21) has to engage with the turn hinge at the side so that the bearing pin and therefore the door are se- cured.

u

uSnap the safety lock (21) onto the turn hinge again.

uPut on the hinge bush Fig. 5 (20).

4.1.3 Transferring the handle

uDisengage the spring clip Fig.7 (34) from the door and transfer it to the new hinge side.

uLift the stopper Fig. 7 (30) out of the door bearing bush and transfer it.

Fig. 7

uDetach door handle Fig. 7 (31), stoppers Fig. 7 (32) and pres- sure plates Fig. 7 (33) plates and transfer to the opposite side

uWhen fitting the pressure plates at the opposite side, pay at- tention that they engage properly.

4.1.4 Fitting the lower door

u Place the door from above onto the lower bearing pin Fig. 5 (22).

u Close the door.

u Insert the upper turn hinge Fig. 4 (12) in the door on the new hinge side.

u Screw down the upper turn hinge Fig. 4 (12)(2 Torx 25) Fig. 4 (13). Possibly make preliminary holes with a bradawl or use a cordless screwdriver.

u Snap the cover Fig. 4 (10) and cover Fig. 4 (11) into place at the opposite side.

4.1.5 Aligning the door

uTransfer the middle screw on the lower turn hinge Fig. 5 (23) into the free oblong hole.

uAlign the door to the appliance housing by way of the two ob- long holes in the lower turn hinge Fig. 5 (23).

uTighten the screws.

4.2 Insertion into a row of kitchen units

(1)	Stack cabinet	Fig. 8
		(3)	Kitchen cabinet
(2)	Appliance	(4)	Wall

The appliance can be inserted into a row of kitchen units. To match the appliance Fig. 8 (2) to the height of the row of units, a suitable stack cabinet Fig.8 (1) can be fitted above the appliance. When inserting the appliance into a row of standard kitchen units (max. depth 580 mm), the appliance can be installed directly next to the kitchen unit Fig. 8 (3). The appliance door projects relative to the front of the kitchen unit by 34 mm at the side and by 50 mm in the middle of the appliance. It can be opened and closed perfectly as a result.

Important for the ventilation:

-At the back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet.

-The ventilation space under the ceiling has to be at least 300 cm2.

-The larger the ventilation space, the more energy-saving the appliance is in operation.

If the appliance is installed with the hinges next to a wall Fig. 8 (4), the distance between appliance and wall has to be at least 36 mm. This corresponds to the projection of the handle when the door is open.

4.3 Transporting the appliance

CAUTION

Risk of injury and danger of damage as a result of incorrect trans- port!

u Transport the appliance in a packed condition. u Transport the appliance upright.

u Do not transport the appliance without assistance.

4.4 Installing the appliance

In the event that the appliance is damaged, contact the supplier immediately before connecting to the mains.

The floor at the site must be flat and level.

Do not install the appliance in a location where it is exposed to direct radiation of the sun, next to a cooker, heater and similar.

5