Liebherr 120309 7084442 - 00 installation instructions Maintenance, Cleaning the appliance

Maintenance

6 Maintenance

6.1 Cleaning the appliance.

Before cleaning:

CAUTION

Risk of injury and damage as a result of hot steam! Hot steam may damage the surfaces and cause burns. u Do not use any steam cleaners!

NOTICE

Incorrect cleaning damages the appliance!

u Do not use cleaning agents in concentrated form.

u Do not use any scouring or abrasive sponges or steel wool. u Do not use any cleaning agents containing sand, chloride,

chemicals or acid.

u Do not use chemical solvents.

u Do not damage or remove the type plate on the inside of the appliance. It is important for the customer service.

u Do not pull off, bend or damage cables or other components. u Do not allow any cleaning water to enter the drain channel,

ventilation grille or electrical parts.

u Empty the appliance. u Pull out the plug.

- Use soft cleaning cloths and a multi-purpose clean- ing agent with neutral pH value.

- Only use food compatible cleaning and care agents on the inside of the appliance.

Outside surfaces and interior:

u Regularly clean ventilation grilles.

w Dust deposits increase energy consumption.

u Clean the plastic surfaces, outside and inside, by hand using lukewarm water and a little washing-up liquid.

NOTICE

The stainless steel doors have a high-quality surface coating and must not be cleaned with the accompanying care product.

Otherwise the surface coating will be affected.

u Wipe the coated door surfaces using a soft, clean cloth only. In case of stubborn dirt, use a little water or a neutral cleaning agent. A microfibre cloth can be optionally used.

u If the stainless steel side walls are dirty, clean them using a commercially available stainless steel cleaning agent. Then evenly apply the accompanying stainless steel care product, making strokes in the direction of the grain.

u Wipe side walls with a paint finish using a soft, clean cloth only. In case of stubborn dirt, use a little water or a neutral cleaning agent. A microfibre cloth can be optionally used.

Clean stainless steel surfaces with a standard stainless steel cleaning agent. Darker areas at the beginning and quite an in- tensive colour of the stainless steel surface are normal.

u Do not apply cleaners to glass or plastic surfaces so as not to scratch them.

u To clean stainless steel surfaces: evenly apply an agent for care of stainless steel, wiping in the direction of the grain.

u To clean the drain opening: remove any deposits with a fine instrument, e.g. a cotton bud.

Items of equipment:

u Clean items of equipment by hand with lukewarm water and a little washing-up liquid.

uTo dismantle the shelves: remove the trims and side parts.

uTo dismantle the storage rack: re- move the protective film from the dec- orative trims.

uLift out the boxes and lift the covers for removal.

After cleaning:

u Wipe dry the appliance and items of equipment. u Connect the appliance and switch it on again. u Put the food back inside.

6.2 Changing the interior light with bulb

Bulb data max. 25 W Fitting: E14

Type of current and voltage must conform with the details on the type plate

uSwitch off the appliance.

uPull out the power plug or switch off the fuse.

uTake holder of the cover Fig. 12 (1) at the front and unhook it at the back.

Change the bulb Fig. 12 (2).

Put the cover Fig. 12 (1)

back in place.uu

Fig. 12

6.3 Changing the interior light with bulb

Bulb data

T25 tube, Philips max. 25 W Fitting: E14

Type of current and voltage must conform with the details on the type plate

Fig.13

uSwitch off the appliance.

uPull out the power plug or switch off the fuse.

uTo remove the cover Fig. 13 (1): put your finger behind the cover and disengage it.

uPull out the glass shelf Fig. 13 (2).

uChange the bulb Fig. 13 (3).

uSlide the glass shelf back in.

uAttach the cover again, engage it at the right and left and pay attention that the middle hook Fig. 13 (4) grips over the glass shelf.

9