Fan bm, Alarm audible signal, SuperCool

food, or to remove or sort out frozen items. Once you have fin- ished placing items in the fridge, or sorting out the items, the electronics automatically adjust the temperature to the most recent setting. A short-term increase in temperature will not affect the frozen food.

W If the display is showing “F 0” to “F 5” the appliance has a fault. Please contact your customer services, and inform them about the indication.This will make it possible to provide fast and ac- curate service.

Alarm - audible signal

The audible warning signal will help you to protect your stored frozen food, and to save energy.

W The audible signal can be shut off by pressing the alarm off button 1,

- automatically once it reaches a temperature sufficient for storing the food safely, or

- when the door is closed.

Door alarm (for fridge section and freezer section)

- This always sounds if the door is kept open for longer than 60 seconds.

The warning signal switch off function is effective while the door is open. Once the door is closed, the alarm function automati- cally resets itself.

Temperature alarm (for freezer section)

- This always sounds if the freezer temperature is not cold enough (it depends on the temperature setting).

- The temperature display flashes at the same time.

This can happen when

- warm, fresh food has been put into the freezer,

- too much warm air gets in while you are sorting out the freezer or removing items.

Thetemperaturedisplaycontinuestoflashuntilthealarmsituation has ended. It then switches from flashing to continuous light. The audible signal is then automatically reset ready for operation.

Fan bm

For cooling by circulated air. If necessary you can use the fan switch if you have large amounts of food to cool down quickly, and you want a relatively even temperature throughout the fridge com- partment on all the shelves. An intensive circulation of air will stop different areas of temperature from forming. All the food is cooled evenly.We recommend using the fan when the room temperature is hot (from approximately 30°C) or when the air humidity is high, for example on hot summer days.

Note: To save energy, the fan automatically switches off when the door is opened. Power consumption rises when the fan is switched on.

SuperCool

You can use the SuperCool button to switch the refrigerator to its maximum cooling power.

We particularly recommend that when freezing large quantities of food, drinks, freshly baked cakes or meals, they should be frozen as quickly as possible.

W Switching on: Briefly press the SuperCool button bl so that it lights.

The cooling temperature goes down to the lowest value. Note: “SuperCool”uses slightly more energy.However after about

6 hours, the electronics system automatically switches back to normal power-saving operation.

If necessary you can also switch on the “SuperCool” function earlier.

W Switching off: press again briefly, until the button light goes out.

Power failure/”FrostControl” display

If a “nA”, symbol appears in the display, this means that:

The freezing temperature has risen too high due to a power failure, or a power cut during the last few hours or days.

W If, while the nA-symbol is showing, you press the alarm off button 1 the warmest temperature that occurred during the power cut is displayed.

Depending on how warm the temperature became, even to the point of defrosting, you should check the quality of the food, and decide how to deal with it!

- This “warmest temperature” displays for approximately one GB minute. After that the electronics system displays the current actual freezing temperature. If you repeatedly press the alarm

off button, you can delete the “warmest temperature” display. When the power cut ends, the appliance continues to operate at the most recent temperature setting.

Additional functions

You can use the setting mode to set the child lock, and change the brilliance of the displays*

Activating the setting mode:

W Press the SuperFrost button for about 5 seconds - the Super-

Frost button flashes - the display indicates c for child lock. Note: The value you are about to alter is flashing.

W Press the Up/Down button to select the function you want: c = child lock,

h = brilliance or

W Now briefly press the SuperFrost button to select/confirm the function:

• For c = child lock press

the Up/Down button c1 = child lock to switch on

c0 = child lockto switch off and confirm with the SuperFrost button.

When the symbol 7 is lit, the child lock is active.

• For h = brillianceselect the Up/Down button h1= minimum to

h5 = maximum brilliance select and and confirm with the SuperFrost button.

Quitting the setting mode:

W Press the On/Off button to quit the setting mode;the electronics setting switches after a period of 2 minutes.

- Normal regulated operation is active again.

Net@Home

Depending on the model and the options, the ap- pliance can also be equipped with an additional connection for a retrofitted Net@Home module. You can connect either a TeleSafe module or a House-bus Module.You can obtain these modules from your dealer.

For technical warranty reasons, the module must be fitted only by customer services.

You will find furtherinformation at our Internet site