Rangemaster U109720 - 01 To Remove or Change a Hotplate Burner, To Change Hotplate Control Taps

Page 28

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have finished.

thermostat capillary

earthing plate

Right hand oven,

The oven thermostat capillary is clamped to the right hand rear upright with an earthing plate.

Remove thermostat phial cover (2 screws). Unclip the thermostat phial from the clips in the oven back.

lead. Fit new electrode to the lead. Fix electrode in burner with screw. Replace burner cap. Check the burner ignition. Replace pan supports.

11.To Remove or Change a Hotplate Burner.

Remove the hotplate tray (see 2).

The burners except the right hand wok burner are mounted on support struts. For these burners, disconnect the burner feed pipes at the burner. Remove the screws at the front and rear holding the support struts. Lift the strut and burners clear. The burners are fixed to the support struts with 2 screws. Remove the appropriate burner and fit the new one. Reassemble in reverse order. Check burner operation is satisfactory.

Feed the thermostat capillary out of the oven. Disconnect wiring from thermostat. Remove 2 screws holding thermostat to mounting panel. Fit new thermostat and reassemble in reverse order. Ensure that the phial is clipped to the oven back with the phial centrally positioned between the clips.

Remember to refit the earthing plate. Check operation of thermostat.

7.To Change Grill Controller

Disconnect from the electricity supply.

Remove the control panel and hotplate (see 1 & 2). Disconnect wiring from controller. Remove 2 screws holding controller to mounting panel. Fit new controller and reassemble in reverse order. Check for correct operation.

BEFORE SERVICING ANY GAS CARRYING COMPONENTS TURN OFF GAS SUPPLY.

8.To Change Hotplate Control Taps

Disconnect from the electricity supply.

Remove the control panel and hotplate (see 1 & 2).

Undo compression fitting at the rear of the tap. Remove the fixings that secure the tap to the gas rail. Remove the tap. Remove and discard the gasket seal. Fit new gasket seal to replacement tap. Re-assemble in reverse order. Check the appliance is gas sound. Check hotplate ignition.

9.To Change Hotplate Burner Injector

Remove burner cap and head. Remove old jet. Fit new injector. Reassemble in reverse order. Check appliance is gas sound.

10.To Change Hotplate Burner Electrode

Lift off pan supports, remove burner cap. Remove the screw holding the electrode. Pull electrode vertically up sufficiently to grip the lead between thumb and forefinger. Pull off the electrode, but keep hold of the

RH Wok burner

Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check burner operation is satisfactory.

12.To Remove an Oven Door

Open oven door and remove Handyrack (where fitted) by springing one side out of the bracket on the door and sliding the other side free.

Door is heavy - take care. Open the oven door. Loosen the two top hinge screws.

Support the weight of the door and remove the screw nearest the hinge pin. Swing the hinge up and away from the hinge pin on the door.

Lift the door away from the bottom hinge. Re-assemble in reverse order.

When replacing the door ensure that the nylon hinge bush is in position between the hinge pin and the hinge bracket at the both the bottom and top.

13.To Change Main Oven Door Outer Panel

Move the cooker forward to gain access to the sides.

Open the oven door slightly and remove the front panel fixing screws from the door sides (two each side).

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Installation & Service Instructions U109720 KitchenerMake sure that the cooker is wired in and switched on Be safeElectricity on Peculiar smellsContents Hob Use only pans that are suitable for ceramic hobsNever cook directly on the surface Grill Remove the pan from the bottom of the grill compartmentOvens Clock To set the time of dayTo time something that’s cooking minute minder To stop automaticallyAuto is showing, you want to reset to manual cooking Cooking using the timerClock Special Features Main Oven shelves Both OvensOven light HandyrackTall oven shelves Page Oven cooking guide Cleaning your cooker GrillHob Control Panel and DoorsMain Oven Tall OvenSide panels of the main oven can be removed Troubleshooting Moving your cookerPower failure Left hand Main oven not coming on when turned on manuallyLeft hand Main oven not coming on when automatic cooking Oven temperature getting hotter as the cooker gets olderPart Finish Recommended Cleaning Method Cleaning Table Outside of cookerOvens General Safety Instructions Clean only parts listed in this guideSpecification of this cooker should not be altered Take care that no water seeps into the applianceDo not use the surface as a cutting board Installation You will also need the following toolsUnpacking the Cooker Positioning the CookerChecking the parts Levelling Moving the CookerFitting a stability bracket Electrical Connection HotplateOven check Fitting the plinthCustomer care Door adjustmentThank you Servicing Notes To Adjust Main Oven Door Catch Keep To Change Grill ControllerTo Remove Grill Door To Remove Main Oven DoorTo Remove or Change a Hotplate Burner To Change Hotplate Control TapsTo Change Hotplate Burner Injector To Change Hotplate Burner ElectrodeTo Adjust the Main Oven Door Catch Keep To Change the Main Oven Door LatchTo Change Tall Oven Door Magnetic Latch To Remove Grill ElementTo Remove Oven Element To Adjust the Oven Door AngleTo change oven light bulb Technical Data DimensionsRatings Ovens1kW 02kW A21.65kW 56kW Key to circuit diagram Colour Code Page Page 271106
Top Page Image Contents