hussman IGFP-R3, R3P-0608 manual Refrigeration Contd, Electrical

Page 13

Rev. 0608

Refrigeration (Cont'd)

Electronic Expansion Valve (Optional)

A wide variety of electronic expansion valves and case controllers can be utilized. Please refer to EEV and controller manufacturers information sheet. Sensors for electronic expansion valves will be installed on the coil inlet, coil outlet, and in the discharge air. (Some supermarkets require a 4th sensor in the return air). Case controllers will be located in the electrical raceway or under the case. The front Self Service Evaporator has an EPR valve installed to maintain a constant discharge temperature. It is located in the front at the right side of the case under the fan plenum near the TX valve.

Thermostatic Expansion Valve Location

This device is located on the same side as the refrigeration stub. A Sporlan balanced port expansion valve model is furnished as standard equipment, unless otherwise specified by customer.

Expansion Valve Adjustment

Expansion valves must be adjusted to fully feed the evaporator. Before attempting any adjustments, make sure the evaporator is either clear or very lightly covered with frost, and that the fixture is within 10°F of its expected operating temperature.

Measuring the Operating Superheat

1.Determine the suction pressure with an accurate pressure gauge at the evaporator outlet.

2.From a refrigerant pressure temperature chart, determine the saturation temperature at the observed suction pressure.

3.Measure the temperature of the suction gas at the thermostatic remote bulb location.

4.Subtract the saturation temperature obtained in step No. 2 from the temperature measured in step No. 3. The difference is superheat.

5.Set the superheat for 5°F - 7°F.

Evaporator Pressure Regulator

An Evaporator Pressure Regulator is installed in the front of the self service section to maintain a constant discharge temperature. It is located at the front right side of the case, under the fan plenum near the TX Valve.

Service Case Temperature Control

Temperature control in the upper section of the R3 with the Service Option is done by means of a thermostat and suction solenoid valve. This controls both temperature and humidity.

T-STAT Location

T-STATS are located within the electrical raceway. Refer to diagram below.

Rear Storage

T-Stat and

Solenoid inside

Storage Area

T-Stat &

Ballast (Located in the same place for hot and cold)

Front Coils controlled by EPR Valve under Deck Pan

(Right side)

Electrical

Wiring Color Code

CASE MUST BE GROUNDED

NOTE: Refer to label affixed to case to determine the actual configuration as checked in the “TYPE INSTALLED” boxes.

Electrical Circuit Identification

Standard lighting for all refrigerated models will be full length fluorescent lamps located within the case at the top.

The switch controlling the lights, the plug provided for digital scale, and the thermometer are located at the rear of the case mullion.

The receptacle that is provided on the exterior back of these models is intended for computerized scales with a five amp maximum load, not for large motors or other high wattage appliances. It should be wired to a dedicated circuit.

Electrical Service Receptacles (When Applicable) The receptacles located on the exterior of the merchandiser are intended for scales and lighted displays. They are not intended nor suitable for large motors or other external appliances.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Ref. Service/self Service/prep caseRev General Instructions Rev Cut and Plan ViewsInstallation Scale Stand Installation Instructions Joint Trim Installation ContdCorner Wedges Wrapping Boards Installation Instructions Install upper support bracket Bumper Installation Instructions Helpful Hints Boston SeriesBoston 2000 Eco Series Boston 1000 Series Installation Refrigeration PlumbingElectrical Refrigeration ContdElectrical Contd Field Wiring and Serial Plate AmperageBallast Location StockingUser Information Contd When cleaningR3 Prep Electrical Wiring DiagramsR3-P-8-REM R3 Top Only Cold120 Wiring DiagramsW0180048 Wiring Diagrams ContdW0180049 Be GroundedR3 & CR3 12 Prep Cases Wiring0608 Contd DiagramsW1800167 R3-P-8-REM120 V L1 15.0 L2 208 V L1 5.0 L2 5.0Loading R3-P-4-REMLight CIRCUIT= 0.7A R3-P-6-REMW0180101 DiagramsContdW0180102 WiringDiagramsW0180103 R3 & CR3 12 TOP only Cold Cases 20.0 Circuit #2 1500WR3TO-2000-4-S/C W1800122Type of Refrigerator Typical Entering Air Temperature Appendix A. Temperature GuidelinesAppendices Appendix B. Application RecommendationsAppendix D. Recommendations to User Appendices ContdAppendices Contd Service Record

IGFP-R3, R3, R3P, R3P-0608, Refrigerated Service and/or Prep with Refrigerated Self Service Front specifications

Hussmann Refrigerated Service and Prep Solutions offer innovative designs and advanced technologies that cater to the dynamic needs of the modern retail environment. Among their impressive line-up, the Refrigerated Self-Service Front models, particularly the R3P-0608 and its variants, stand out for their effective combination of functionality, energy efficiency, and user-friendly features.

The R3P series exemplifies Hussmann's commitment to providing high-quality refrigeration solutions that enhance customer experience. With a sleek design, these service fronts are not only appealing but also practical for various food service applications, including convenience stores and grocery operations. The self-service model allows customers easy access to a wide range of products, ensuring a seamless shopping experience whether it’s for pre-packaged meals, salads, or beverages.

One of the main features of the R3P series is its energy-efficient technology. Equipped with advanced refrigeration systems, these models operate effectively while maintaining optimal food temperatures. Hussmann integrates Eco-Design principles into the R3P, which help reduce its overall energy consumption without compromising performance. This is vital in today's retail environment, where operational costs continue to rise, and sustainability is a key customer concern.

The innovative design of the R3P also includes adjustable shelving and customizable display options, enabling retailers to optimize space for various product types. This flexibility allows businesses to display items clearly and attractively while maximizing visual appeal and accessibility. Additionally, the ergonomic design of the glass doors ensures easy access for both customers and staff, streamlining operations and improving product visibility.

The IGFP-R3 variant further exemplifies Hussmann's advanced technology with integrated features such as smart temperature controls and monitoring systems. This variant is designed to enhance food safety by ensuring that products are kept at the recommended temperatures, providing peace of mind to both retailers and consumers.

Overall, Hussmann Refrigerated Service and Prep solutions, particularly the R3P-0608 and related models, represent an ideal blend of style, efficiency, and functionality. The emphasis on energy savings, customization, and food safety makes these solutions integral to the success of modern food retail and service environments. As retailers continue to seek competitive edges, the R3P series by Hussmann remains a leading choice in refrigeration technology, offering exceptional value and innovation.
Top Page Image Contents