Clamshell Assembly, Install Glass | hussman IGHT-ESH/ESHS-0010

IGHT-ESH/ESHS-0010

Lift-up Glass

IMPORTANT!

READ BEFORE RAISING FRONT GLASS :

CLAMSHELL ASSEMBLY

(1) PVC U-CHANNEL

The top cylinders, which allow the raising and lowering of the glass, have been carefully tested for proper ten- sion. However, during shipment, the clamshell screws can work themselves out and/or the lubricant inside may have settled. This settling may cause excessive or uneven tension on the glass - to the point of breakage.

(2) RUBBER SEALER

GASKET

Before Rasing the Glass retighten all

screws along clamshell!

SILICONE

(3) HANDRAIL

(5) SUPPORT

After installing new cylinders, it is advisable to perform these three easy steps before completely raising the front

(4) TAPE SECURELY

AROUND THE

WHOLE END

INSTALL GLASS

ANGLE

glass.

1.Slowly raise and lower each glass section 6 times, to a height of 6".

2.Increase the height to 12", and raise and lower the glass 6 more times.

3.Finally, raise the glass to it's full extension. This should release any settled lubricant in the cylinders, and prevent any stress on the front glass. (1)(3)

ESH Curved Glass

Replacement

BROKEN GLASS REMOVAL

1.Loosen set screws along clamp.

2.Remove plastic PVC channel (1) between clamshell and glass.

3.Use new plastic PVC channel. Lift off top of clamshell, and clean off any particles. Replace clamshell (Do NotTighten).

NEW GLASS PREP

1.Centering rubber gasket (2) on handrail, slide all but outer 3" of gasket into handrail.

2.Apply 3/8" bead of buytl to outer 2" of handrail, and insert remaining gasket. Trim to length of handrail.

3.Apply 3/8" bead of buytl to bottom of glass receiver

(3) on handrail.

4.Center handrail on glass. Firmly push onto bottom edge of glass.

5.Tape securely (4), and allow 12 hours to cure.

NOTE: Do not tape where glass support angles are located on case (approximately 11-13" from ends).

1.Place PVC U-channel (1) on glass.

2.With one person holding each end of the glass, lift up and place top of glass inside clamshell (glass will be in fully open position.) Center glass within clamshell.

3.With one person holding the glass in the clamshell, tighten the two set screw on each end and two equally spaced set screws in the center of the glass to about 4 ft/lbs.

4.Open and close glass gently, checking to see that the alignment can be corrected by releasing the set screws enough to move the glass forward and backward.

5.Glass should rest squarely on glass support angles

(5). If not, they can be adjusted by loosening the screw that attaches them to the case.

6.After glass is aligned, tighten set screws.

7.Attach wipes to appropriate edge of glass filling gap between adjacent pieces of glass. See “Installing Glass Sweep” section for complete instructions.

8.Leave taped glass closed for 12 hours.

INSTALLING GLASS SWEEP

After installing new glass onto a case, it is important to replace the glass sweep.

Masking Tape

Front Glass

Glass Sweep

IGHT-ESH/ESHS-0010 specifications

The Hussman IGHT-ESH/ESHS-0010 is a state-of-the-art refrigeration unit designed specifically for commercial applications. Renowned for its durability and efficiency, this unit stands out in the competitive landscape of commercial refrigeration. With a focus on energy conservation and environmental responsibility, the IGHT-ESH/ESHS-0010 incorporates advanced technologies that enhance its performance while reducing operational costs.

One of the standout features of the Hussman IGHT-ESH/ESHS-0010 is its innovative refrigeration system. Utilizing a highly efficient compressor, the unit ensures optimal cooling performance while minimizing energy consumption. This efficiency is further enhanced by the incorporation of variable speed fans, which automatically adjust their speed based on the cooling demand. This feature not only improves energy efficiency but also reduces noise levels, making it suitable for a variety of commercial environments.

The design of the IGHT-ESH/ESHS-0010 emphasizes versatility and adaptability. It is equipped with adjustable shelving and modular components, allowing users to customize the interior layout according to their specific needs. This flexibility makes it an excellent choice for retailers, foodservice establishments, and convenience stores that require dynamic display and storage solutions.

Temperature control is crucial in refrigeration, and the Hussman IGHT-ESH/ESHS-0010 excels in this area. Featuring advanced digital controls and monitoring systems, users can easily set and adjust temperatures to meet their requirements. The unit provides consistent temperature management, which is essential for preserving the quality and safety of perishable products.

Another remarkable aspect of the IGHT-ESH/ESHS-0010 is its focus on sustainability. The unit is designed with environmentally friendly refrigerants that comply with today’s stringent regulations, contributing to reduced greenhouse gas emissions. Additionally, the Hussman brand is committed to energy-efficient solutions that not only benefit the environment but also help businesses save on energy costs.

Finally, the construction of the Hussman IGHT-ESH/ESHS-0010 is robust, featuring high-quality materials that ensure longevity and resilience in a busy commercial setting. Its attractive exterior design ensures that it seamlessly fits into any retail or foodservice environment while providing exceptional cooling performance.

In summary, the Hussman IGHT-ESH/ESHS-0010 is a centerpiece in modern commercial refrigeration. With its combination of energy efficiency, user-friendly features, and sustainable design, it represents a smart investment for businesses aiming to enhance their operational efficiency and environmental stewardship.