Corner Wedges

IGHT-ESH/ESHS-0010

Installation cont.

LEVELING

IMPORTANT! IT IS IMPERATIVE THAT CASES BE LEVELED FROM FRONT TO BACK AND SIDE TO SIDE PRIOR TO JOINING. A LEVEL CASE IS NECESSARY TO INSURE PROPER OPERATION, WATER DRAINAGE, GLASS ALIGNMENT, AND OPERATION OF THE HINGES SUPPORTING THE GLASS. LEVELING THE CASE CORRECTLY WILL SOLVE MOST HINGE OPERATION PROBLEMS.

NOTE: A. To avoid removing concrete flooring, begin lineupleveling from the highest point of the store floor.

B.When wedges are involved in a lineup, set them first.

C.If there is a problem with the hinge operation, first check if case is level. The mini top hardware may have become loosened during shipping (ESHS Only). If it does not look level, call Hussmann Chino immediately for the shim kit needed to level the mini top hardware, and continue with the following instructions. (If problem still persists, see "Clamshell Screw Adjustment" section – ESH only).

It is the contractor's responsibility to install case(s) according to local construction and health codes.

6.Slide second case up to first case snugly. Then level second case to the first case so glass front, bumper and top are flush.

7.To compress buytl at joint, use two Jurgenson wood clamps. Make sure case is level from front to back and side to side on inside bulkheads at joint.

8.Attach sections together via a 2 bolts located in the base of the case. Secure the overhead structure by bolting the bracket, located inside behind lights.

Do not use cam locks to pull cases together!

All cases were leveled and joined prior to shipment to insure the closest possible fit when cases are joined in the field. When joining, use a carpenters level and shim legs accordingly. Case must be raised correctly, under legs where support is best, to prevent damage to case.

LEVELING/JOINING INSTRUCTIONS

1.Check level of floor where cases are to be set. Determine the highest point of the floor; cases will be set off this point.

2.Set first case, and adjust legs over the highest part of the floor so that case is level. Prevent damage – case must be raised under leg or by use of 2x6 or 2x4 leg brace. Remove side and back leg braces after case is set.

3.Set second case as close as possible to the first case, and level case to the first using the instructions in step one.

4.Apply masking tape 1/8" in from end of case on inside and outside rear mullion on both cases to be joined.

5.Apply liberal bead of case joint sealant (butyl) to dotted area shown in (Fig.2,#1) of first case. Apply heavy amount to cover entire shaded area.

DO NOT USE PERMAGUM!

9.Apply bead of buytl to top of bulkheads and slip on stainless steel bulkhead cap. Also apply buytl to seam between overhead light tubes.

10.VERY IMPORTANT! Apply liberal amounts of black buytl to area under interior lower legs and fill all voids down to bulkhead.

11.Use finger to smooth buytl as thin as possible at masking tape on inside and outside of rear mullion (apply additional buytl if necessary). Remove tape applied on line #3.

Corner wedges are attached via front and rear camlocks. Use a 7mm allen wrench to turn the locks. Do not over- tighten! Join the top by using a joint bracket (included in joint kit) with 3/8" bolts.

COMMON END BETWEEN UNLIKE CASES AND HOT CASES

Bolt end onto case using bolts provided in predrilled holes behind front panel through bracket provided, and in the rear behind the rear access panel on the bottom. Hot case are only bolted in two places.

IGHT-ESH/ESHS-0010 specifications

The Hussman IGHT-ESH/ESHS-0010 is a state-of-the-art refrigeration unit designed specifically for commercial applications. Renowned for its durability and efficiency, this unit stands out in the competitive landscape of commercial refrigeration. With a focus on energy conservation and environmental responsibility, the IGHT-ESH/ESHS-0010 incorporates advanced technologies that enhance its performance while reducing operational costs.

One of the standout features of the Hussman IGHT-ESH/ESHS-0010 is its innovative refrigeration system. Utilizing a highly efficient compressor, the unit ensures optimal cooling performance while minimizing energy consumption. This efficiency is further enhanced by the incorporation of variable speed fans, which automatically adjust their speed based on the cooling demand. This feature not only improves energy efficiency but also reduces noise levels, making it suitable for a variety of commercial environments.

The design of the IGHT-ESH/ESHS-0010 emphasizes versatility and adaptability. It is equipped with adjustable shelving and modular components, allowing users to customize the interior layout according to their specific needs. This flexibility makes it an excellent choice for retailers, foodservice establishments, and convenience stores that require dynamic display and storage solutions.

Temperature control is crucial in refrigeration, and the Hussman IGHT-ESH/ESHS-0010 excels in this area. Featuring advanced digital controls and monitoring systems, users can easily set and adjust temperatures to meet their requirements. The unit provides consistent temperature management, which is essential for preserving the quality and safety of perishable products.

Another remarkable aspect of the IGHT-ESH/ESHS-0010 is its focus on sustainability. The unit is designed with environmentally friendly refrigerants that comply with today’s stringent regulations, contributing to reduced greenhouse gas emissions. Additionally, the Hussman brand is committed to energy-efficient solutions that not only benefit the environment but also help businesses save on energy costs.

Finally, the construction of the Hussman IGHT-ESH/ESHS-0010 is robust, featuring high-quality materials that ensure longevity and resilience in a busy commercial setting. Its attractive exterior design ensures that it seamlessly fits into any retail or foodservice environment while providing exceptional cooling performance.

In summary, the Hussman IGHT-ESH/ESHS-0010 is a centerpiece in modern commercial refrigeration. With its combination of energy efficiency, user-friendly features, and sustainable design, it represents a smart investment for businesses aiming to enhance their operational efficiency and environmental stewardship.