Multiquip manual Stow CMS-94S Concrete Mixer Basic Engine Components

Page 14
INITIAL SERVICING
The engine (Figure 3) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing.
Honda GX Series Engine Shown

STOW CMS-94S CONCRETE MIXER — BASIC ENGINE COMPONENTS

Figure 3. Engine Controls and Components

5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel.

6. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture.

1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.

WARNING

Adding fuel to the tank should be accomplished only when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill,

DO NOT attempt to start the engine until the fuel residue has been completely wiped up, and the area surrounding the engine is dry.

2. Throttle Lever – Used to adjust engine RPM speed (lever advanced forward SLOW, lever back toward operator FAST).

3.

Engine ON/OFF Switch – ON position permits engine

 

starting, OFF position stops engine operations.

4.

Recoil Starter (pull rope) – Manual-starting method. Pull

 

the starter grip until resistance is felt, then pull briskly and

 

smoothly.

7. Air Cleaner – Prevents dirt and other debris from entering the fuel system. Remove wing-nut on top of air filter cannister to gain access to filter element.

NOTE

Operating the engine without an air filter, with a damaged air filter, or a filter in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

8. Spark Plug – Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). Clean spark plug once a week.

9. Muffler – Used to reduce noise and emissions.

WARNING

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating. NEVER

operate the engine with the muffler removed.

10. Fuel Tank – Holds unleaded gasoline. For additional information refer to engine owner's manual.

PAGE 14 —STOW CMS-94S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #2 (08/04/06)

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Concrete Mixer Page Heres HOW to GET Help Stow CMS-94SCONCRETE Mixer Table of Contents CMS-94S Concrete Mixer Parts Ordering Procedures Stow CMS-94S Concrete Mixer Specifications Stow CMS-94S Concrete Mixer Dimensions Mixer Stow CMS-94S Safety Message Alert Symbols General Safety Stow CMS-94S Concrete Mixer Rules for Safe OperationMaintenance Safety EmergenciesStow CMS-94S Concrete Mixer Operation and Safety Decals Machine Safety DecalsStow CMS-94S Concrete Mixer General Information Stow CMS-94S Concrete Mixer Mixer Basic Components Mixer Major ComponentsStow CMS-94S Concrete Mixer Basic Engine Components Starting, OFF position stops engine operationsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pentile and LoopStow CMS-94S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Connection Electric Motor Voltage Change SwitchElectric Motor Single Phase Electric Motor with 12 inch Pigtail Cable Stow CMS-94S Concrete Mixer Electric MotorStow CMS-94S Concrete Mixer PRE-INSPECTION GAS Engine Stow CMS-94S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyStarting the Electric Motor Stow CMS-94S Concrete Mixer Initial START-UP ELECT. MotorInitial Start-up Instructions Electric Motor Starting Stopping the Mixer Electric Stow CMS-94S Concrete Mixer OperationOperation Stow CMS-94S Concrete Mixer Maintenance Engine Stow CMS-94S Concrete Mixer Maintenance Engine MaintenanceStow CMS-94S Concrete Mixer Maintenance Mixer Stow CMS-94S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page Stow CMS-94S Concrete Mixer Troubleshooting Engine Engine TroubleshootingStow CMS-94S Concrete Mixer -TROUBLESHOOTING ENG./MIXER Engine TroubleshootingExplanation of Codes in Remarks Column Stow CMS-94S Concrete Mixer Suggested Spare Parts DescriptionStow CMS-94S Concrete Mixer Name Plate and Decals Name Plate and DecalsDECAL, Emergency Stop DECAL, Safety InstructionsStow Logo CIPDCL160 DECAL, Crush Warning DECAL, Towing InstructionsSteel Barrel Assy King PIN HOUSING, JackshaftPLUG, Expansion Spindle Bearing ConeMain Frame Assy WASHER, Lock 1/4 Handwheel Safety ChainGUARD, Gear Wheel Dump GearAxle Assy Spring Leaf Lock NUT 5/8 NCSpring Support AxleCabinet Assy Latch ASSY., Complete Rubber Protector Includes Item WWASHER, Flat 5/16 WASHER, Lock 5/16GAS Engine Mounting Plate Assy Square KEY 1/4 X 40 MM SWITCH, StopENGINE, Honda 8.0 HP Upper PulleyStow CMS-94S- Electric Motor Mounting Plate Assembly Electric Motor Mounting Plate AssyLower Pulley MOTOR, Electric 1.5 HPBelt B-59 AIR Cleaner Assy GROMMET, AIR Cleaner ELEMENT, AIR CLEANER, DualCOVER, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy ROD Push SPRING, Weight ReturnCamshaft ARM Valve RockerCarburetor Assy Valve SET, Float PLATE, Lever SettingGasket SET Float SETHonda GX240K1QA2 Engine Control Assy Control AssyBOLT, Governor ARM NUT, SELF- Lock 6MM Honda GX240K1QA2 Engine Control AssySPRING, Cable Return NUT, FlangeCrankcase Cover Assy PIN, Governor Weight WEIGHT, GovernorHOLDER, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Honda GX240K1QA2 Engine Crankshaft AssyCylinder Barrel Assy BOLT, Drain Plug Switch ASSY., OIL LevelSHAFT, Governor ARM Ring 14MM AraiCylinder Head Assy CLIP, Valve Guide GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional GASKET, Cylinder HeadFAN Cover Assy CLIP, Tube Switch ASSY., Engine StopCLIP, Wire Harness ShroudFlywheel Assy NUT, Special 16MM FAN, CoolingFlywheel Comp KEY, Special WoodruffMuffler Assy PROTECTOR, EX. Pipe MufflerPROTECTOR, Muffler PIPE, EXFuel Tank Assy Tank COMP., Fuel *NH1*, Black Rubber Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPIgnition Coil Assy Coil ASSY., Ignition GROMMET, WireWIRE, Stop Switch 370MM CAP ASSY., Noise SuppressorPiston Assy Ring SET, PISTON, 0.75, Optional BOLT, Connecting RODRing SET, PISTON, STD PISTON, StandardRecoil Starter Assy SPRING, Friction PULLEY, Recoil StarterRATCHET, Starter SPRING, Starter ReturnLabel Assy MARK, CAUTION, External Labels AssyEMBLEM, Internal LABEL, CautionPayment Terms Page Service DEPARTMENT/TECHNICAL Assistance

CMS-94S specifications

The Multiquip CMS-94S is a remarkable piece of machinery in the realm of concrete mixing, designed to meet the demands of both professional contractors and DIY enthusiasts. With its robust design and advanced features, this concrete mixer is indispensable for a variety of construction projects.

One of the standout features of the CMS-94S is its powerful engine. It is equipped with a reliable Honda GX240 engine that delivers outstanding performance and efficiency. This 8 HP engine ensures that the mixer operates smoothly, even under heavy loads, making it ideal for large-scale projects where time is of the essence.

Durability is a key characteristic of the Multiquip CMS-94S. The drum is constructed from high-quality steel, which not only extends its lifespan but also allows it to withstand the rigors of demanding job sites. The mixer has a capacity of 9 cubic feet, allowing users to mix a significant amount of concrete in one go. This feature greatly enhances productivity, reducing the number of batches needed for larger jobs.

The design of the CMS-94S also prioritizes user convenience and safety. It features a tipping mechanism that provides easy dumping of mixed concrete, ensuring minimal waste and easy cleanup. The ergonomically designed handles allow for a comfortable grip, making it easier to maneuver the mixer even on uneven terrain.

In terms of technology, the CMS-94S incorporates a belt-driven mixer, which is less prone to wear and tear compared to direct-drive systems. This technology ensures quieter operation, lower maintenance needs, and improved overall reliability.

Safety is also a top priority in the design of the CMS-94S. The mixer includes protective guards and safety interlocks that help prevent accidents during operation. This not only protects the operator but also ensures that the machine remains in optimal condition.

Additionally, the Multiquip CMS-94S is designed for easy transportation. It comes with large wheels that facilitate movement across construction sites without hassle, allowing for quick repositioning as work progresses.

In summary, the Multiquip CMS-94S embodies the ideal blend of power, efficiency, and durability. With its advanced features, reliable engine, and safety mechanisms, it stands out as a trusted choice for concrete mixing needs, catering to professionals and DIY projects alike.
Top Page Image Contents