Multiquip CMS-94S manual Tow Bar to Vehicle Connection Coupler Only

Page 16

STOW CMS-94S CONCRETE MIXER —TOWING GUIDELINES

Towing Safety Precautions

CAUTION:

Check with your county or state safety towing regulations department before towing your mixer.

To reduce the possibility of an accident while transporting the mixer on public roads, always make sure that the mixer towing components and the towing vehicle are in good operating condition and both units are mechanically sound.

The following list of suggestions should be used when towing the mixer:

Make sure that the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer "gross vehicle weight rating" (GVWR).

ALWAYS inspect the hitch and coupling for wear. NEVER tow the mixer with defective hitches, couplings, chains etc.

CHECK the tire air pressure on both the towing vehicle and the trailer. Also check the tire tread wear on both vehicles.

ALWAYS make sure the mixer is equipped with a "Safety Chain".

ALWAYS attach trailer's safety chain to the frame of towing vehicle.

ALWAYS make sure that the towing vehicle's directional, backup, and brake lights are working properly.

Remember in most cases the maximum speed unless otherwise posted for highway towing is 45 MPH, however before towing your mixer, check your local state, and county vehicle towing requirements. Recommended off-road towing is not to exceed 10 MPH or less depending on type of terrain.

Place chocked blocks underneath wheels to prevent rolling, while parked, if disconnected from towing vehicle.

Inflate tires to correct pressure, inspect tires for cuts, and excessive wear. See Table 16 (Tire Wear Troubleshooting).

When towing of the mixer is required, place the drum in the up position (mouth facing upwards).

ALWAYS make sure that the fuel valve lever is in the OFF position (gasoline models only).

Check wheel mounting lug nuts with a torque wrench. Torque wheel lug nuts as described in the maintenance section of this manual.

Check tightness of U-clamp nuts, torque suspension hardware as referenced in the maintenance section of this manual.

Avoid sudden stops and starts.This can cause skidding, or jackknifing. Smooth, gradual starts and stops will improve gas milage.

Avoid sharp turns to prevent rolling.

CAUTION:

If the mixer tow bar is deformed or damaged replace entire tow bar. NEVER tow the mixer with a defective tow bar. There exist the possibility of the trailer separating from the towing vehicle.

Tow Bar to Vehicle Connection (Coupler Only)

1.Check the vehicle hitch ball, and mixer's coupler for signs of wear or damage. Replace any parts that are worn or damaged before towing.

2.Use only a 2-inch ball diameter (towing vehicle), this will match the mixer's 2-inch coupler. Use of any other ball diameter will create an extremely dangerous condition which can result in separation of the coupler and ball or ball failure.

3.After tow bar has been connected to mixer (see next page), attach mixer's coupler to the hitch ball on the towing vehicle securely and make sure the lock lever is in the down position (locked).

Mixer Tow Bar Vehicle Connection (Pentile and Loop)

1.Make sure the bumper on the towing vehicle is equipped to handle either a pentile or loop type tow bar configuration.

2.After tow bar has been connected to mixer (see next page), secure either type of tow bar to the towing vehicle, following state and county towing regulations.

3.As a minimum, use a 1/2-inch bolt and nylock nut grade 5 when securing either tow bar to the towing vehicle,

PAGE 16 —STOW CMS-94S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #2 (08/04/06)

Image 16
Contents Concrete Mixer Page Heres HOW to GET Help Stow CMS-94SCONCRETE Mixer Table of Contents CMS-94S Concrete Mixer Parts Ordering Procedures Stow CMS-94S Concrete Mixer Specifications Stow CMS-94S Concrete Mixer Dimensions Mixer Stow CMS-94S Safety Message Alert Symbols General Safety Stow CMS-94S Concrete Mixer Rules for Safe OperationMaintenance Safety EmergenciesStow CMS-94S Concrete Mixer Operation and Safety Decals Machine Safety DecalsStow CMS-94S Concrete Mixer General Information Stow CMS-94S Concrete Mixer Mixer Basic Components Mixer Major ComponentsStow CMS-94S Concrete Mixer Basic Engine Components Starting, OFF position stops engine operationsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pentile and LoopStow CMS-94S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Electric Motor Voltage Change SwitchElectric Motor Connection Single Phase Electric Motor with 12 inch Pigtail Cable Stow CMS-94S Concrete Mixer Electric MotorStow CMS-94S Concrete Mixer PRE-INSPECTION GAS Engine Stow CMS-94S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyInitial Start-up Instructions Electric Motor Starting Stow CMS-94S Concrete Mixer Initial START-UP ELECT. MotorStarting the Electric Motor Operation Stow CMS-94S Concrete Mixer OperationStopping the Mixer Electric Stow CMS-94S Concrete Mixer Maintenance Engine Stow CMS-94S Concrete Mixer Maintenance Engine MaintenanceStow CMS-94S Concrete Mixer Maintenance Mixer Stow CMS-94S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page Stow CMS-94S Concrete Mixer Troubleshooting Engine Engine TroubleshootingStow CMS-94S Concrete Mixer -TROUBLESHOOTING ENG./MIXER Engine TroubleshootingExplanation of Codes in Remarks Column Stow CMS-94S Concrete Mixer Suggested Spare Parts DescriptionStow CMS-94S Concrete Mixer Name Plate and Decals Name Plate and DecalsDECAL, Safety Instructions Stow Logo CIPDCL160 DECAL, Crush WarningDECAL, Emergency Stop DECAL, Towing InstructionsSteel Barrel Assy HOUSING, Jackshaft PLUG, ExpansionKing PIN Spindle Bearing ConeMain Frame Assy Handwheel Safety Chain GUARD, Gear WheelWASHER, Lock 1/4 Dump GearAxle Assy Lock NUT 5/8 NC Spring SupportSpring Leaf AxleCabinet Assy Rubber Protector Includes Item W WASHER, Flat 5/16Latch ASSY., Complete WASHER, Lock 5/16GAS Engine Mounting Plate Assy SWITCH, Stop ENGINE, Honda 8.0 HPSquare KEY 1/4 X 40 MM Upper PulleyStow CMS-94S- Electric Motor Mounting Plate Assembly Electric Motor Mounting Plate AssyBelt B-59 MOTOR, Electric 1.5 HPLower Pulley AIR Cleaner Assy ELEMENT, AIR CLEANER, Dual COVER, AIR CleanerGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy SPRING, Weight Return CamshaftROD Push ARM Valve RockerCarburetor Assy PLATE, Lever Setting Gasket SETValve SET, Float Float SETHonda GX240K1QA2 Engine Control Assy Control AssyHonda GX240K1QA2 Engine Control Assy SPRING, Cable ReturnBOLT, Governor ARM NUT, SELF- Lock 6MM NUT, FlangeCrankcase Cover Assy WEIGHT, Governor HOLDER, Governor WeightPIN, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Honda GX240K1QA2 Engine Crankshaft AssyCylinder Barrel Assy Switch ASSY., OIL Level SHAFT, Governor ARMBOLT, Drain Plug Ring 14MM AraiCylinder Head Assy GUIDE, VALVE, OS, Optional GUIDE, EX. VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Switch ASSY., Engine Stop CLIP, Wire HarnessCLIP, Tube ShroudFlywheel Assy FAN, Cooling Flywheel CompNUT, Special 16MM KEY, Special WoodruffMuffler Assy Muffler PROTECTOR, MufflerPROTECTOR, EX. Pipe PIPE, EXFuel Tank Assy Rubber Supporter 107MM JOINT, Fuel TankTank COMP., Fuel *NH1*, Black GASKET, Fuel Filler CAPIgnition Coil Assy GROMMET, Wire WIRE, Stop Switch 370MMCoil ASSY., Ignition CAP ASSY., Noise SuppressorPiston Assy BOLT, Connecting ROD Ring SET, PISTON, STDRing SET, PISTON, 0.75, Optional PISTON, StandardRecoil Starter Assy PULLEY, Recoil Starter RATCHET, StarterSPRING, Friction SPRING, Starter ReturnLabel Assy Labels Assy EMBLEM, InternalMARK, CAUTION, External LABEL, CautionPayment Terms Page Service DEPARTMENT/TECHNICAL Assistance

CMS-94S specifications

The Multiquip CMS-94S is a remarkable piece of machinery in the realm of concrete mixing, designed to meet the demands of both professional contractors and DIY enthusiasts. With its robust design and advanced features, this concrete mixer is indispensable for a variety of construction projects.

One of the standout features of the CMS-94S is its powerful engine. It is equipped with a reliable Honda GX240 engine that delivers outstanding performance and efficiency. This 8 HP engine ensures that the mixer operates smoothly, even under heavy loads, making it ideal for large-scale projects where time is of the essence.

Durability is a key characteristic of the Multiquip CMS-94S. The drum is constructed from high-quality steel, which not only extends its lifespan but also allows it to withstand the rigors of demanding job sites. The mixer has a capacity of 9 cubic feet, allowing users to mix a significant amount of concrete in one go. This feature greatly enhances productivity, reducing the number of batches needed for larger jobs.

The design of the CMS-94S also prioritizes user convenience and safety. It features a tipping mechanism that provides easy dumping of mixed concrete, ensuring minimal waste and easy cleanup. The ergonomically designed handles allow for a comfortable grip, making it easier to maneuver the mixer even on uneven terrain.

In terms of technology, the CMS-94S incorporates a belt-driven mixer, which is less prone to wear and tear compared to direct-drive systems. This technology ensures quieter operation, lower maintenance needs, and improved overall reliability.

Safety is also a top priority in the design of the CMS-94S. The mixer includes protective guards and safety interlocks that help prevent accidents during operation. This not only protects the operator but also ensures that the machine remains in optimal condition.

Additionally, the Multiquip CMS-94S is designed for easy transportation. It comes with large wheels that facilitate movement across construction sites without hassle, allowing for quick repositioning as work progresses.

In summary, the Multiquip CMS-94S embodies the ideal blend of power, efficiency, and durability. With its advanced features, reliable engine, and safety mechanisms, it stands out as a trusted choice for concrete mixing needs, catering to professionals and DIY projects alike.