Multiquip manual Stow CMS-94S Concrete Mixer Maintenance Mixer

Page 26

STOW CMS-94S CONCRETE MIXER — MAINTENANCE (MIXER)

Ball Socket and Clamp Face Maintenance

1.If the towing vechicle is equipped with a ball socket, smear socket periodically with multi-purpose grease. This will keep the ball socket well lubricated.

2.Periodically oil pivot points and clamp face surfaces of coupler with SAE 30 WT. motor oil.

2.Use Poleyrex EM (Exxon Mobil) or equalivant lubricant. Clean grease fitting, apply grease gun to fitting (1/2 shot). Remember too much grease or injecting grease too quickly can cause premature bearing failure. Slowly apply the recommended amount of grease, taking a miniute or so to apply.

3.When parking or storing your mixer. Keep the coupler off the ground so dirt will not build up in the ball socket.

Grease Fittings (Zerk) Maintenance (Mixer)

There are 3 grease (Figure 27) fittings that will require lubrication. Lubricate these fittings once a week. Use lithium base grease, grade N0.1.

Figure 27. Grease Fittings Mixer

Grease Fittings (Zerk) Maintenance (Electric Motor)

1.There are two grease (Figure 28) fittings at each end of the electric motor that will require lubrication. Lubricate these fittings about every 16 months.

Wheel Bearings

1.After every 3 months of operation, remove the hub dust cap and inspect the wheel bearings (Figure 29). Once a year, or when required, disassemble the wheel hubs remove the old grease and repack the bearings forcing grease between rollers, cone and cage with a good grade of high speed wheel bearing grease (never use grease heavier than 265 A.S.T.M.penetration (“No. 2.”)

Figure 29. Wheel Hub and Bearings

2.Fill the wheel hub (Figure 29) with grease to the inside diameter of the outer races and also fill the hub grease cap. Reassemble the hub and mount the wheel. Then tighten the adjusting nut, at the same time turn the wheel in both directions, until there is a slight bind to be sure all the bearing surfaces are in contact.

Then back-off the adjusting nut 1/6 to 1/4 turn or to the nearest locking hole or sufficiently to allow the wheel to rotate freely within limits of .001" to .010" end play.Lock the nut at this position. Install the cotter pin and dust cap, and tighten all hardware.

Mixer Cleaning

 

1.

For thorough mix and longer drum life, always wash drum

 

 

out after each use.

Figure 28. Grease Fittings Electric Motor

2.

NEVER! pour or spray water over the engine or electric

 

motor.

 

 

PAGE 26 —STOW CMS-94S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #2 (08/04/06)

Image 26
Contents Concrete Mixer Page Heres HOW to GET Help Stow CMS-94SCONCRETE Mixer Table of Contents CMS-94S Concrete Mixer Parts Ordering Procedures Stow CMS-94S Concrete Mixer Specifications Stow CMS-94S Concrete Mixer Dimensions Mixer Stow CMS-94S Safety Message Alert Symbols General Safety Stow CMS-94S Concrete Mixer Rules for Safe OperationMaintenance Safety EmergenciesStow CMS-94S Concrete Mixer Operation and Safety Decals Machine Safety DecalsStow CMS-94S Concrete Mixer General Information Stow CMS-94S Concrete Mixer Mixer Basic Components Mixer Major ComponentsStow CMS-94S Concrete Mixer Basic Engine Components Starting, OFF position stops engine operationsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pentile and LoopStow CMS-94S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Connection Electric Motor Voltage Change SwitchElectric Motor Single Phase Electric Motor with 12 inch Pigtail Cable Stow CMS-94S Concrete Mixer Electric MotorStow CMS-94S Concrete Mixer PRE-INSPECTION GAS Engine Stow CMS-94S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyStarting the Electric Motor Stow CMS-94S Concrete Mixer Initial START-UP ELECT. MotorInitial Start-up Instructions Electric Motor Starting Stopping the Mixer Electric Stow CMS-94S Concrete Mixer OperationOperation Stow CMS-94S Concrete Mixer Maintenance Engine Stow CMS-94S Concrete Mixer Maintenance Engine MaintenanceStow CMS-94S Concrete Mixer Maintenance Mixer Stow CMS-94S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page Stow CMS-94S Concrete Mixer Troubleshooting Engine Engine TroubleshootingStow CMS-94S Concrete Mixer -TROUBLESHOOTING ENG./MIXER Engine TroubleshootingExplanation of Codes in Remarks Column Stow CMS-94S Concrete Mixer Suggested Spare Parts DescriptionStow CMS-94S Concrete Mixer Name Plate and Decals Name Plate and DecalsDECAL, Emergency Stop DECAL, Safety InstructionsStow Logo CIPDCL160 DECAL, Crush Warning DECAL, Towing InstructionsSteel Barrel Assy King PIN HOUSING, JackshaftPLUG, Expansion Spindle Bearing ConeMain Frame Assy WASHER, Lock 1/4 Handwheel Safety ChainGUARD, Gear Wheel Dump GearAxle Assy Spring Leaf Lock NUT 5/8 NCSpring Support AxleCabinet Assy Latch ASSY., Complete Rubber Protector Includes Item WWASHER, Flat 5/16 WASHER, Lock 5/16GAS Engine Mounting Plate Assy Square KEY 1/4 X 40 MM SWITCH, StopENGINE, Honda 8.0 HP Upper PulleyStow CMS-94S- Electric Motor Mounting Plate Assembly Electric Motor Mounting Plate AssyLower Pulley MOTOR, Electric 1.5 HPBelt B-59 AIR Cleaner Assy GROMMET, AIR Cleaner ELEMENT, AIR CLEANER, DualCOVER, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy ROD Push SPRING, Weight ReturnCamshaft ARM Valve RockerCarburetor Assy Valve SET, Float PLATE, Lever SettingGasket SET Float SETHonda GX240K1QA2 Engine Control Assy Control AssyBOLT, Governor ARM NUT, SELF- Lock 6MM Honda GX240K1QA2 Engine Control AssySPRING, Cable Return NUT, FlangeCrankcase Cover Assy PIN, Governor Weight WEIGHT, GovernorHOLDER, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Honda GX240K1QA2 Engine Crankshaft AssyCylinder Barrel Assy BOLT, Drain Plug Switch ASSY., OIL LevelSHAFT, Governor ARM Ring 14MM AraiCylinder Head Assy CLIP, Valve Guide GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional GASKET, Cylinder HeadFAN Cover Assy CLIP, Tube Switch ASSY., Engine StopCLIP, Wire Harness ShroudFlywheel Assy NUT, Special 16MM FAN, CoolingFlywheel Comp KEY, Special WoodruffMuffler Assy PROTECTOR, EX. Pipe MufflerPROTECTOR, Muffler PIPE, EXFuel Tank Assy Tank COMP., Fuel *NH1*, Black Rubber Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPIgnition Coil Assy Coil ASSY., Ignition GROMMET, WireWIRE, Stop Switch 370MM CAP ASSY., Noise SuppressorPiston Assy Ring SET, PISTON, 0.75, Optional BOLT, Connecting RODRing SET, PISTON, STD PISTON, StandardRecoil Starter Assy SPRING, Friction PULLEY, Recoil StarterRATCHET, Starter SPRING, Starter ReturnLabel Assy MARK, CAUTION, External Labels AssyEMBLEM, Internal LABEL, CautionPayment Terms Page Service DEPARTMENT/TECHNICAL Assistance

CMS-94S specifications

The Multiquip CMS-94S is a remarkable piece of machinery in the realm of concrete mixing, designed to meet the demands of both professional contractors and DIY enthusiasts. With its robust design and advanced features, this concrete mixer is indispensable for a variety of construction projects.

One of the standout features of the CMS-94S is its powerful engine. It is equipped with a reliable Honda GX240 engine that delivers outstanding performance and efficiency. This 8 HP engine ensures that the mixer operates smoothly, even under heavy loads, making it ideal for large-scale projects where time is of the essence.

Durability is a key characteristic of the Multiquip CMS-94S. The drum is constructed from high-quality steel, which not only extends its lifespan but also allows it to withstand the rigors of demanding job sites. The mixer has a capacity of 9 cubic feet, allowing users to mix a significant amount of concrete in one go. This feature greatly enhances productivity, reducing the number of batches needed for larger jobs.

The design of the CMS-94S also prioritizes user convenience and safety. It features a tipping mechanism that provides easy dumping of mixed concrete, ensuring minimal waste and easy cleanup. The ergonomically designed handles allow for a comfortable grip, making it easier to maneuver the mixer even on uneven terrain.

In terms of technology, the CMS-94S incorporates a belt-driven mixer, which is less prone to wear and tear compared to direct-drive systems. This technology ensures quieter operation, lower maintenance needs, and improved overall reliability.

Safety is also a top priority in the design of the CMS-94S. The mixer includes protective guards and safety interlocks that help prevent accidents during operation. This not only protects the operator but also ensures that the machine remains in optimal condition.

Additionally, the Multiquip CMS-94S is designed for easy transportation. It comes with large wheels that facilitate movement across construction sites without hassle, allowing for quick repositioning as work progresses.

In summary, the Multiquip CMS-94S embodies the ideal blend of power, efficiency, and durability. With its advanced features, reliable engine, and safety mechanisms, it stands out as a trusted choice for concrete mixing needs, catering to professionals and DIY projects alike.