Multiquip CMS-94S manual To tighten wheel lug nuts

Page 28

STOW CMS-94S CONCRETE MIXER — MAINTENANCE (MIXER)

Lug Nut Torque Requirements

It is extremely important to apply and maintain proper wheel mounting torque on the trailer. Be sure to use only the fas- teners matched to the cone angle of the wheel. Proper pro- cedure for attachment of the wheels is as follows:

1. Start all wheel lug nuts by hand.

2. Torque all lug nuts in sequence. See Figure 31. DO NOT torque the wheel lug nuts all the way down.Tighten each lug nut in 3 separate passes as defined by Table 10.

3. After first road use, retorque all lug nuts in sequence. Check all wheel lug nuts periodically.

NOTE

NEVER! use an pneumatic air gun

 

to tighten wheel lug nuts.

Mixer Storage

For storage of the mixer for over 30 days, the following is recommended:

z Drain the fuel tank completely, or add STA-BIL to the fuel.

z Run the engine until the fuel is completely consumed.

z Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage.

z Clean the entire mixer and engine compartment.

z Place the mixing drum in the down position (mouth facing downward).

z Cover the mixer and place it a clean dry area, that is protected from harsh elements.

Figure 31. Wheel Lug Nuts Tightening Sequence

PAGE 28 —STOW CMS-94S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #2 (08/04/06)

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Concrete Mixer Page Heres HOW to GET Help Stow CMS-94SCONCRETE Mixer Table of Contents CMS-94S Concrete Mixer Parts Ordering Procedures Stow CMS-94S Concrete Mixer Specifications Stow CMS-94S Concrete Mixer Dimensions Mixer Stow CMS-94S Safety Message Alert Symbols General Safety Stow CMS-94S Concrete Mixer Rules for Safe OperationMaintenance Safety EmergenciesStow CMS-94S Concrete Mixer Operation and Safety Decals Machine Safety DecalsStow CMS-94S Concrete Mixer General Information Stow CMS-94S Concrete Mixer Mixer Basic Components Mixer Major ComponentsStow CMS-94S Concrete Mixer Basic Engine Components Starting, OFF position stops engine operationsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pentile and LoopStow CMS-94S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Electric Motor Voltage Change SwitchElectric Motor Connection Single Phase Electric Motor with 12 inch Pigtail Cable Stow CMS-94S Concrete Mixer Electric MotorStow CMS-94S Concrete Mixer PRE-INSPECTION GAS Engine Stow CMS-94S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyInitial Start-up Instructions Electric Motor Starting Stow CMS-94S Concrete Mixer Initial START-UP ELECT. MotorStarting the Electric Motor Operation Stow CMS-94S Concrete Mixer OperationStopping the Mixer Electric Stow CMS-94S Concrete Mixer Maintenance Engine Stow CMS-94S Concrete Mixer Maintenance Engine MaintenanceStow CMS-94S Concrete Mixer Maintenance Mixer Stow CMS-94S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page Stow CMS-94S Concrete Mixer Troubleshooting Engine Engine TroubleshootingStow CMS-94S Concrete Mixer -TROUBLESHOOTING ENG./MIXER Engine TroubleshootingExplanation of Codes in Remarks Column Stow CMS-94S Concrete Mixer Suggested Spare Parts DescriptionStow CMS-94S Concrete Mixer Name Plate and Decals Name Plate and DecalsDECAL, Safety Instructions Stow Logo CIPDCL160 DECAL, Crush WarningDECAL, Emergency Stop DECAL, Towing InstructionsSteel Barrel Assy HOUSING, Jackshaft PLUG, ExpansionKing PIN Spindle Bearing ConeMain Frame Assy Handwheel Safety Chain GUARD, Gear WheelWASHER, Lock 1/4 Dump GearAxle Assy Lock NUT 5/8 NC Spring SupportSpring Leaf AxleCabinet Assy Rubber Protector Includes Item W WASHER, Flat 5/16Latch ASSY., Complete WASHER, Lock 5/16GAS Engine Mounting Plate Assy SWITCH, Stop ENGINE, Honda 8.0 HPSquare KEY 1/4 X 40 MM Upper PulleyStow CMS-94S- Electric Motor Mounting Plate Assembly Electric Motor Mounting Plate AssyBelt B-59 MOTOR, Electric 1.5 HPLower Pulley AIR Cleaner Assy ELEMENT, AIR CLEANER, Dual COVER, AIR CleanerGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy SPRING, Weight Return CamshaftROD Push ARM Valve RockerCarburetor Assy PLATE, Lever Setting Gasket SETValve SET, Float Float SETHonda GX240K1QA2 Engine Control Assy Control AssyHonda GX240K1QA2 Engine Control Assy SPRING, Cable ReturnBOLT, Governor ARM NUT, SELF- Lock 6MM NUT, FlangeCrankcase Cover Assy WEIGHT, Governor HOLDER, Governor WeightPIN, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Honda GX240K1QA2 Engine Crankshaft AssyCylinder Barrel Assy Switch ASSY., OIL Level SHAFT, Governor ARMBOLT, Drain Plug Ring 14MM AraiCylinder Head Assy GUIDE, VALVE, OS, Optional GUIDE, EX. VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Switch ASSY., Engine Stop CLIP, Wire HarnessCLIP, Tube ShroudFlywheel Assy FAN, Cooling Flywheel CompNUT, Special 16MM KEY, Special WoodruffMuffler Assy Muffler PROTECTOR, MufflerPROTECTOR, EX. Pipe PIPE, EXFuel Tank Assy Rubber Supporter 107MM JOINT, Fuel TankTank COMP., Fuel *NH1*, Black GASKET, Fuel Filler CAPIgnition Coil Assy GROMMET, Wire WIRE, Stop Switch 370MMCoil ASSY., Ignition CAP ASSY., Noise SuppressorPiston Assy BOLT, Connecting ROD Ring SET, PISTON, STDRing SET, PISTON, 0.75, Optional PISTON, StandardRecoil Starter Assy PULLEY, Recoil Starter RATCHET, StarterSPRING, Friction SPRING, Starter ReturnLabel Assy Labels Assy EMBLEM, InternalMARK, CAUTION, External LABEL, CautionPayment Terms Page Service DEPARTMENT/TECHNICAL Assistance

CMS-94S specifications

The Multiquip CMS-94S is a remarkable piece of machinery in the realm of concrete mixing, designed to meet the demands of both professional contractors and DIY enthusiasts. With its robust design and advanced features, this concrete mixer is indispensable for a variety of construction projects.

One of the standout features of the CMS-94S is its powerful engine. It is equipped with a reliable Honda GX240 engine that delivers outstanding performance and efficiency. This 8 HP engine ensures that the mixer operates smoothly, even under heavy loads, making it ideal for large-scale projects where time is of the essence.

Durability is a key characteristic of the Multiquip CMS-94S. The drum is constructed from high-quality steel, which not only extends its lifespan but also allows it to withstand the rigors of demanding job sites. The mixer has a capacity of 9 cubic feet, allowing users to mix a significant amount of concrete in one go. This feature greatly enhances productivity, reducing the number of batches needed for larger jobs.

The design of the CMS-94S also prioritizes user convenience and safety. It features a tipping mechanism that provides easy dumping of mixed concrete, ensuring minimal waste and easy cleanup. The ergonomically designed handles allow for a comfortable grip, making it easier to maneuver the mixer even on uneven terrain.

In terms of technology, the CMS-94S incorporates a belt-driven mixer, which is less prone to wear and tear compared to direct-drive systems. This technology ensures quieter operation, lower maintenance needs, and improved overall reliability.

Safety is also a top priority in the design of the CMS-94S. The mixer includes protective guards and safety interlocks that help prevent accidents during operation. This not only protects the operator but also ensures that the machine remains in optimal condition.

Additionally, the Multiquip CMS-94S is designed for easy transportation. It comes with large wheels that facilitate movement across construction sites without hassle, allowing for quick repositioning as work progresses.

In summary, the Multiquip CMS-94S embodies the ideal blend of power, efficiency, and durability. With its advanced features, reliable engine, and safety mechanisms, it stands out as a trusted choice for concrete mixing needs, catering to professionals and DIY projects alike.
Top Page Image Contents