Multiquip EM-70S EM-70 PLASTER/MORTAR Mixer Safety Chain Connection, Always Tow with, Drum Saftey

Page 13

EM-70 PLASTER/MORTAR MIXER — SAFETY CHAIN CONNECTION

 

CAUTION

Always Tow with

 

a Safety Chain

 

 

NEVER! tow the mixer with the safety chain removed. The safety chain is intended to prevent complete separation of the mixer from the towing vehicle in the event of a tow bar failure.

Reference Figure 2 for the installation of the safety chain.

Tow Bar to Mixer Connection

1.Insert the tow bar through the round opening at the bottom of the mixer stand.

Align the hole on the tow bar with the hole on the mixer frame, and insert 1/2-inch bolt through tow bar and frame. Secure tow bar to frame with 1/2-inch nylock nut.Tighten to 40 ft.-lbs.

2.Route the safety chain through the holes just above the tow bar, located on each side of the mixer stand.

Loop the chain together and place under the tow bar. Secure the loop with the connector link.

3.extend the safety chain along the length of the tow bar, looping it through the tow bar's connector link. Remove any excess chain slack.

4.Connect the free end of (connector link) the safety chain to the towing vehicle. Remember it is critical that the length of the chain be properly adjusted, to prevent the draw bar and the front of the mixer stand from dropping to the the ground (contact) in the event the draw bar becomes disconnected from the towing vehicle.

 

CAUTION

Drum Saftey

 

when Towing

 

 

DO NOT tow the mixer unless the mixing drum is completely empty. ALWAYS make sure the drum latch pin is fully engaged to the right (Figure 3) of the drum stop block. This will keep the drum from rotating.

Figure 3. Drum Latch Pin (Tow or Locked Position)

Figure 2. Tow Bar and Safety Chain Installation

EM-70 PLASTER/MORTAR MIXER — OPERATION MANUAL — REV. #1 (008/10/04) — PAGE 13

Image 13
Contents Model EM-70S Steel Model EM-70P Plastic Page Email mq@multiquip.com Wilmington Ave Carson, CAEM-70 PLASTER/MORTAR Mixer -TABLE of Contents Direct TOLL-FREE access Capacity Cu. ft 198 liters EM-70 PLASTER/MORTAR Mixer SpecificationsDescription Dimensions in. cm EM-70 PLASTER/MORTAR Mixer DimensionsInstructions for data relative to its safe operation EM-70 PLASTER/MORTAR Mixer Safety Message Alert SymbolsBurn Hazards Respiratory HazardsEquipment Damage Always wear approved eye and hearing protectionRead this manual EM-70 PLASTER/MORTAR Mixer Rules for Safe OperationNever operate the mixer in an explosive atmosphere or near Never pour or spray water over the engine or electric motor Mixer when in useStand Clear EM-70 PLASTER/MORTAR Mixer -TOWING Guidelines Towing Safety Precautions Regularly InspectTow Bar toVehicle Connection Coupler Only ReplacingWhen Towing EM-70 PLASTER/MORTAR Mixer Safety Chain ConnectionAlways Tow with Tow Bar to Mixer ConnectionMachine Safety Decals EM-70 PLASTER/MORTAR Mixer Operation and Safety DecalsEM-70 PLASTER/MORTAR Mixer General Information Mixer Components EM-70 PLASTER/MORTAR Mixer Major ComponentsInitial Servicing EM-70 PLASTER/MORTAR Mixer Engine ComponentsExplosive Burn HazardElectric Motor EM-70 PLASTER/MORTAR Mixer Electric MotorElectric Motor Connection Important!, when changing the input Electric Motor Voltage SwitchEM-70 PLASTER/MORTAR Mixer Electric Motor Replace the voltage lock-out boltPaddle Blade Adjustment Steel Drum Adjust paddles as shown in aPaddle Blade Adjustment Poly Drum Adjust paddles as shown in bBefore Starting EM-70 PLASTER/MORTAR Mixer InspectionInspection Engine Oil CheckEM-70 PLASTER/MORTAR Mixer Inspection General Safety EM-70 PLASTER/MORTAR Mixer START-UP ProcedureStart-up ProcedureGasonline Engine Respiratory HazardEngine ON/OFF Switch Dump Handle Safety EM-70 PLASTER/MORTAR Mixer START-UP/OPERATION ProceduresMixing Dumping OFF position EM-70 PLASTER/MORTAR Mixer SHUT-DOWN ProceduresStop the engine Engine after every useEngine Maintenance Schedule EM-70 PLASTER/MORTAR Mixer Maintenance EngineMaintenance EM-70 PLASTER/MORTAR Mixer Maintenance EngineExplosive Hazard Ball Socket and Clamp Face Maintenance EM-70 PLASTER/MORTAR Mixer Maintenance MixerDrum Head Seals Drum Bearing Bracket LubricationCountershaft Bearing Lubrication EM-70 PLASTER/MORTAR Mixer Maintenance MixerMain Gear and Drive Pinion Alignment Inspect Tooth Contact between Main Gear and Drive Pinion Grease Fittings Zerk Maintenance Electric MotorGear Lubrication TiresWear/InflationStart all wheel lug nuts by hand Lug NutTorque RequirementsKeep Hands SuspensionMixer Storage Engine Troubleshooting EM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING EngineWhite EM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING EngineEM-70PLASTER/MORTARMIXER-TROUBLESHOOTINGMIXER/ELECTRICMOTOR EM-70 PLASTER/MORTAR Mixer -WIRING Diagram Electric Motor Page Multiquip INC

EM-70S, EM-70P specifications

The Multiquip EM-70P and EM-70S are two robust and versatile electric generators designed to provide reliable power for various applications, ranging from construction sites to special events. Both models are renowned for their performance, durability, and efficiency, catering to the needs of contractors, event organizers, and outdoor enthusiasts alike.

One of the standout features of the EM-70P and EM-70S is their powerful engine. The EM-70P is equipped with a 7,000-watt gasoline engine, while the EM-70S comes with a 7,000-watt propane engine. This dual-fuel capability of the EM-70S not only enhances flexibility but also promotes cleaner and more efficient energy consumption. Both generators feature a heavy-duty steel frame that ensures maximum durability and protection against the rigors of job sites.

Technologically, these generators are designed with advanced noise reduction features. The low-noise operation makes them suitable for use in noise-sensitive environments, such as residential areas and events, allowing users to work or host gatherings without disturbing neighbors. Additionally, the EM-70P and EM-70S are equipped with an easy-to-read control panel, featuring circuit breakers and outlets that include multiple 120V and 240V options, ensuring compatibility with a wide range of tools and equipment.

Another notable characteristic of the EM-70P and EM-70S is their portability. Both models come with sturdy wheels and a foldable handle, making them easy to transport on job sites or during events. Their compact size does not compromise power output, as they can easily handle the demands of multiple tools and devices simultaneously.

Safety is also prioritized in the design of these generators. They feature a low-oil shutdown system which automatically turns off the engine when oil levels are critically low, preventing potential damage. Furthermore, the generators are designed to withstand harsh weather conditions, providing peace of mind to users who require dependable power in any environment.

In summary, the Multiquip EM-70P and EM-70S generators combine powerful performance, noise-reduction technology, user-friendly controls, and safety features. Whether you need a reliable power source for construction, outdoor events, or emergency backup, these generators present an ideal solution that meets diverse power needs efficiently and effectively.