Multiquip EM-70P, EM-70S EM-70 PLASTER/MORTAR Mixer Electric Motor, Electric Motor Connection

Page 18

EM-70 PLASTER/MORTAR MIXER — ELECTRIC MOTOR

Electric Motor

For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the motor.

Protect the electric motor from dust as much as possible and keep ventilating openings clean.

 

CAUTION

Electric Motor

 

Safety

DO NOT spray water at any time on the electric motor.

DO NOT operate electric motor in a explosive environment.

The electric motor used in this mixer is a single-phase 1.5 HP motor. The input voltage requirement for this motor is either 115 or 230 VAC only.

Electric Motor Connection

A12-inch electrical cable (Figure 7) is provided with the electrical motor for hookup to a power source.Table 5 shows the required NEMA connector for the desired motor horsepower rating. In addition, Table 5 also shows the matching NEMA approved connector for the required extension cord.

 

CAUTION

Electric Motor

 

Connections

 

 

ALWAYS make certain that the power source required for the electric motor is correct and always use the correct NEMA configuration plug. Failure to supply the correct voltage to the motor can severely damage the motor.

TABLE 5. ELECTRIC MOTOR WIRING INFORMATION

Motor

115-230 VAC - Single Phase

 

 

Horsepower

NEMA Plug Connector

Mating NEMA

Rating

Receptacle Connector

 

 

 

 

 

1.5 HP

L5-20P P/N EM940537

L5-20R P/N EM940538

(115 VAC)

 

 

 

 

 

1.5 HP

L6-20P P/N 940539

L6-20R P/N 940540

(230 VAC)

 

 

 

 

 

NOTE It is strongly recommended that all electrical wiring be done by a licensed electrician.

Special attention should be given to the electric switch as well as the over-and-under voltage protection devices as per regulations set forth in the local electrical safety code handbook

Figure 7. Single Phase Electric Motor With

12-inch Pigtail

PAGE 18 — EM-70 PLASTER/MORTAR MIXER — OPERATION MANUAL — REV. #1 (008/10/04)

Image 18
Contents Model EM-70S Steel Model EM-70P Plastic Page Wilmington Ave Carson, CA Email mq@multiquip.comEM-70 PLASTER/MORTAR Mixer -TABLE of Contents Direct TOLL-FREE access EM-70 PLASTER/MORTAR Mixer Specifications Capacity Cu. ft 198 litersEM-70 PLASTER/MORTAR Mixer Dimensions Description Dimensions in. cmBurn Hazards EM-70 PLASTER/MORTAR Mixer Safety Message Alert SymbolsInstructions for data relative to its safe operation Respiratory HazardsAlways wear approved eye and hearing protection Equipment DamageEM-70 PLASTER/MORTAR Mixer Rules for Safe Operation Read this manualNever operate the mixer in an explosive atmosphere or near Mixer when in use Never pour or spray water over the engine or electric motorStand Clear Tow Bar toVehicle Connection Coupler Only Towing Safety Precautions Regularly InspectEM-70 PLASTER/MORTAR Mixer -TOWING Guidelines ReplacingAlways Tow with EM-70 PLASTER/MORTAR Mixer Safety Chain ConnectionWhen Towing Tow Bar to Mixer ConnectionEM-70 PLASTER/MORTAR Mixer Operation and Safety Decals Machine Safety DecalsEM-70 PLASTER/MORTAR Mixer General Information EM-70 PLASTER/MORTAR Mixer Major Components Mixer ComponentsExplosive EM-70 PLASTER/MORTAR Mixer Engine ComponentsInitial Servicing Burn HazardEM-70 PLASTER/MORTAR Mixer Electric Motor Electric MotorElectric Motor Connection EM-70 PLASTER/MORTAR Mixer Electric Motor Electric Motor Voltage SwitchImportant!, when changing the input Replace the voltage lock-out boltAdjust paddles as shown in a Paddle Blade Adjustment Steel DrumAdjust paddles as shown in b Paddle Blade Adjustment Poly DrumInspection EM-70 PLASTER/MORTAR Mixer InspectionBefore Starting Engine Oil CheckEM-70 PLASTER/MORTAR Mixer Inspection Start-up ProcedureGasonline Engine EM-70 PLASTER/MORTAR Mixer START-UP ProcedureGeneral Safety Respiratory HazardEngine ON/OFF Switch EM-70 PLASTER/MORTAR Mixer START-UP/OPERATION Procedures Dump Handle SafetyMixing Dumping Stop the engine EM-70 PLASTER/MORTAR Mixer SHUT-DOWN ProceduresOFF position Engine after every useEM-70 PLASTER/MORTAR Mixer Maintenance Engine Engine Maintenance ScheduleEM-70 PLASTER/MORTAR Mixer Maintenance Engine MaintenanceExplosive Hazard Drum Head Seals EM-70 PLASTER/MORTAR Mixer Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationEM-70 PLASTER/MORTAR Mixer Maintenance Mixer Countershaft Bearing LubricationMain Gear and Drive Pinion Alignment Gear Lubrication Grease Fittings Zerk Maintenance Electric MotorInspect Tooth Contact between Main Gear and Drive Pinion TiresWear/InflationLug NutTorque Requirements Start all wheel lug nuts by handSuspension Keep HandsMixer Storage EM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine Engine TroubleshootingEM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine WhiteEM-70PLASTER/MORTARMIXER-TROUBLESHOOTINGMIXER/ELECTRICMOTOR EM-70 PLASTER/MORTAR Mixer -WIRING Diagram Electric Motor Page Multiquip INC

EM-70S, EM-70P specifications

The Multiquip EM-70P and EM-70S are two robust and versatile electric generators designed to provide reliable power for various applications, ranging from construction sites to special events. Both models are renowned for their performance, durability, and efficiency, catering to the needs of contractors, event organizers, and outdoor enthusiasts alike.

One of the standout features of the EM-70P and EM-70S is their powerful engine. The EM-70P is equipped with a 7,000-watt gasoline engine, while the EM-70S comes with a 7,000-watt propane engine. This dual-fuel capability of the EM-70S not only enhances flexibility but also promotes cleaner and more efficient energy consumption. Both generators feature a heavy-duty steel frame that ensures maximum durability and protection against the rigors of job sites.

Technologically, these generators are designed with advanced noise reduction features. The low-noise operation makes them suitable for use in noise-sensitive environments, such as residential areas and events, allowing users to work or host gatherings without disturbing neighbors. Additionally, the EM-70P and EM-70S are equipped with an easy-to-read control panel, featuring circuit breakers and outlets that include multiple 120V and 240V options, ensuring compatibility with a wide range of tools and equipment.

Another notable characteristic of the EM-70P and EM-70S is their portability. Both models come with sturdy wheels and a foldable handle, making them easy to transport on job sites or during events. Their compact size does not compromise power output, as they can easily handle the demands of multiple tools and devices simultaneously.

Safety is also prioritized in the design of these generators. They feature a low-oil shutdown system which automatically turns off the engine when oil levels are critically low, preventing potential damage. Furthermore, the generators are designed to withstand harsh weather conditions, providing peace of mind to users who require dependable power in any environment.

In summary, the Multiquip EM-70P and EM-70S generators combine powerful performance, noise-reduction technology, user-friendly controls, and safety features. Whether you need a reliable power source for construction, outdoor events, or emergency backup, these generators present an ideal solution that meets diverse power needs efficiently and effectively.