Multiquip EM-70P, EM-70S EM-70 PLASTER/MORTAR Mixer Inspection, Before Starting, Engine Oil Check

Page 22

EM-70 PLASTER/MORTAR MIXER — INSPECTION

Before Starting

1.Read all safety instructions at the beginning of manual.

2.Clean the mixer, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

4.Check carburetor for external dirt and dust. Clean with dry compressed air.

5.Check fastening nuts and bolts for tightness.

 

CAUTION

Eyesight and Hearing

 

Protection

 

 

ALWAYS wear approved eye and hearing protection before operating the mixer.

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

4.If the oil level is low (Figure 10), fill to the edge of the oil filler hole with the recommended oil type (Table 7). Maximum oil capacity is 2.33 pints (1.09 liters)

NOTE

Reference manufacturer

 

engine manual for specific

 

servicing instructions.

 

CAUTION

Inspection &

 

Maintenance Saftey

 

 

NEVER place hands or feet inside the engine guard cover while the engine is running. ALWAYS shut the engine down before performing any kind of maintenance service on the mixer.

Engine Oil Check

1.To check the engine oil level, place the mixer on secure level ground with the engine stopped.

Figure 10. Engine Oil Dipstick (Oil Level)

TABLE 7. OIL TYPE

Season

Temperature

Oil Type

 

 

 

Summer

25°C or Higher

SAE 10W-30

 

 

 

Spring/Fall

25°C~10°C

SAE 10W-30/20

 

 

 

Winter

0°C or Lower

SAE 10W-10

 

 

 

2.Remove the filler dipstick from the engine oil filler hole (Figure 9) and wipe it clean.

Figure 9. Engine Oil Dipstick (Removal)

PAGE 22 — EM-70 PLASTER/MORTAR MIXER — OPERATION MANUAL — REV. #1 (008/10/04)

Image 22
Contents Model EM-70S Steel Model EM-70P Plastic Page Wilmington Ave Carson, CA Email mq@multiquip.comEM-70 PLASTER/MORTAR Mixer -TABLE of Contents Direct TOLL-FREE access EM-70 PLASTER/MORTAR Mixer Specifications Capacity Cu. ft 198 litersEM-70 PLASTER/MORTAR Mixer Dimensions Description Dimensions in. cmBurn Hazards EM-70 PLASTER/MORTAR Mixer Safety Message Alert SymbolsInstructions for data relative to its safe operation Respiratory HazardsAlways wear approved eye and hearing protection Equipment DamageRead this manual EM-70 PLASTER/MORTAR Mixer Rules for Safe OperationNever operate the mixer in an explosive atmosphere or near Never pour or spray water over the engine or electric motor Mixer when in useStand Clear Tow Bar toVehicle Connection Coupler Only Towing Safety Precautions Regularly InspectEM-70 PLASTER/MORTAR Mixer -TOWING Guidelines ReplacingAlways Tow with EM-70 PLASTER/MORTAR Mixer Safety Chain ConnectionWhen Towing Tow Bar to Mixer ConnectionEM-70 PLASTER/MORTAR Mixer Operation and Safety Decals Machine Safety DecalsEM-70 PLASTER/MORTAR Mixer General Information EM-70 PLASTER/MORTAR Mixer Major Components Mixer ComponentsExplosive EM-70 PLASTER/MORTAR Mixer Engine ComponentsInitial Servicing Burn HazardElectric Motor EM-70 PLASTER/MORTAR Mixer Electric MotorElectric Motor Connection EM-70 PLASTER/MORTAR Mixer Electric Motor Electric Motor Voltage SwitchImportant!, when changing the input Replace the voltage lock-out boltAdjust paddles as shown in a Paddle Blade Adjustment Steel DrumAdjust paddles as shown in b Paddle Blade Adjustment Poly DrumInspection EM-70 PLASTER/MORTAR Mixer InspectionBefore Starting Engine Oil CheckEM-70 PLASTER/MORTAR Mixer Inspection Start-up ProcedureGasonline Engine EM-70 PLASTER/MORTAR Mixer START-UP ProcedureGeneral Safety Respiratory HazardEngine ON/OFF Switch Dump Handle Safety EM-70 PLASTER/MORTAR Mixer START-UP/OPERATION ProceduresMixing Dumping Stop the engine EM-70 PLASTER/MORTAR Mixer SHUT-DOWN ProceduresOFF position Engine after every useEM-70 PLASTER/MORTAR Mixer Maintenance Engine Engine Maintenance ScheduleMaintenance EM-70 PLASTER/MORTAR Mixer Maintenance EngineExplosive Hazard Drum Head Seals EM-70 PLASTER/MORTAR Mixer Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationCountershaft Bearing Lubrication EM-70 PLASTER/MORTAR Mixer Maintenance MixerMain Gear and Drive Pinion Alignment Gear Lubrication Grease Fittings Zerk Maintenance Electric MotorInspect Tooth Contact between Main Gear and Drive Pinion TiresWear/InflationLug NutTorque Requirements Start all wheel lug nuts by handKeep Hands SuspensionMixer Storage EM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine Engine TroubleshootingEM-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING Engine WhiteEM-70PLASTER/MORTARMIXER-TROUBLESHOOTINGMIXER/ELECTRICMOTOR EM-70 PLASTER/MORTAR Mixer -WIRING Diagram Electric Motor Page Multiquip INC

EM-70S, EM-70P specifications

The Multiquip EM-70P and EM-70S are two robust and versatile electric generators designed to provide reliable power for various applications, ranging from construction sites to special events. Both models are renowned for their performance, durability, and efficiency, catering to the needs of contractors, event organizers, and outdoor enthusiasts alike.

One of the standout features of the EM-70P and EM-70S is their powerful engine. The EM-70P is equipped with a 7,000-watt gasoline engine, while the EM-70S comes with a 7,000-watt propane engine. This dual-fuel capability of the EM-70S not only enhances flexibility but also promotes cleaner and more efficient energy consumption. Both generators feature a heavy-duty steel frame that ensures maximum durability and protection against the rigors of job sites.

Technologically, these generators are designed with advanced noise reduction features. The low-noise operation makes them suitable for use in noise-sensitive environments, such as residential areas and events, allowing users to work or host gatherings without disturbing neighbors. Additionally, the EM-70P and EM-70S are equipped with an easy-to-read control panel, featuring circuit breakers and outlets that include multiple 120V and 240V options, ensuring compatibility with a wide range of tools and equipment.

Another notable characteristic of the EM-70P and EM-70S is their portability. Both models come with sturdy wheels and a foldable handle, making them easy to transport on job sites or during events. Their compact size does not compromise power output, as they can easily handle the demands of multiple tools and devices simultaneously.

Safety is also prioritized in the design of these generators. They feature a low-oil shutdown system which automatically turns off the engine when oil levels are critically low, preventing potential damage. Furthermore, the generators are designed to withstand harsh weather conditions, providing peace of mind to users who require dependable power in any environment.

In summary, the Multiquip EM-70P and EM-70S generators combine powerful performance, noise-reduction technology, user-friendly controls, and safety features. Whether you need a reliable power source for construction, outdoor events, or emergency backup, these generators present an ideal solution that meets diverse power needs efficiently and effectively.