U-Line U-2175RFS-00 manual Re-installation of Drawer, Top-to-Bottom and Left-to-Right Adjustment

Page 21

Minor Adjustment:

Note: The mounting holes on the slide are slightly larger than the screws’ diameter.

Screws Should

Be Loose

Minor Adjustment:

Note: The mounting holes on the slide are slightly larger than the screws’ diameter.

1.Loosen one slide’s mounting screws.

2.Level the slide.

3.Retighten the screws.

4.Repeat procedure for the other slide.

Severe Adjustment:

Level the Slide

1.Loosen one slide’s mounting screws.

2.Push the slide upward or downward to match the position of the other slide.

3.Retighten the screws.

4.Repeat the procedure with the other slide if necessary.

Mounting Screws

Push Slide

Upward or

Downward

Note: The slides have extra mounting holes that may be used.

1. Loosen one slide’s rear

Severe Adjustment:

Note: The slides have extra mounting holes that may be used.

 

mounting screws.

Mark and Drill New

2.

Remove the slide’s front

Mounting Holes

 

 

mounting screws.

 

3.

Reposition the slide so it is

 

 

level.

 

4.

Mark new front drilling holes

 

 

using a different set of

Level the Slide

 

mounting holes on the slide.

 

5. Drill the new holes with a #30 drill bit.

1.Remove one slide’s mounting screws.

2.Reposition the slide so it is the same distance from the bottom of the liner as the other slide. Measure to confirm.

3.Mark new drilling holes using different sets of mounting holes on the slide.

Mark and Drill New

Mounting Holes

Push Slide

Upward or

Downward

6.

Remount the slide.

7.

Repeat procedure for the other slide.

Top-to-Bottom (and Left-to-Right) Adjustment:

The drawer will need a Top-to-Bottom Adjustment if, when viewed from the front, the drawer is not level horizontally. Viewed from the top, one side will protrude. This is caused by one of the slides being mounted higher than the other slide on the unit’s liner.

Not Aligned

Top-to-Bottom

Not Aligned Left-to-Right

FrontView of Unit

TopView of Unit

Note: Front location holes are shown. Corresponding rear holes will also need to be marked.

4.Drill all the new holes with a #30 drill bit.

5.Remount the slide.

Re-installation of Drawer

!CAUTION

Use care when handling the drawer. Drawer edges, drawer rail and the unit’s slide may be sharp.

1.Set the drawer’s rails onto the slides.

2.Re-install the rails’ mounting screws.

3.Plug in the drawer’s connection wiring (top drawer only).

18

u-line.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 2175RFS-00 2175RFB-002175RFS-01 2175RFW-00Please Record Your Model Information Read and save this Use and Care GuideTable of Contents General Precautions Safety Alert DefinitionsIce Makers Features Combo Model FeaturesControl Systems Adjusting Air TemperatureAir Flow Initial StartupChecking Product Temperature To check the actual product temperature in the unitInterior Lighting Touch Electronic Control Quick GuideTo turn the unit on or off Control DialAdjusting Air Temperature Drawers CrispersTop Storage Bin Ice Maker Adjustment Ice Maker OperationInterval As Required Leveling Removing and Installing Interior ShelvesRemoving and Installing Grille Removing and Installing Door ShelvesInstalling the grille Door Alignment and Adjustment To align and adjust the doorDoor Systems Reversing Black or White Doors Door ReversabilityPrepare door for reinstallation Install DoorAlign and adjust the door To reverse the door Remove grille Reversing the DoorRemove top hinge, and door Remove bottom hingePrepare door for reinstallation For black or white doors Install bottom hingeInstall top hinge, and door Install grilleChecking Drawer Alignment Adjusting Drawer AlignmentTop-to-Bottom and Left-to-Right Adjustment Re-installation of DrawerExterior Cleaning Interior CleaningDefrosting Storage, Vacation and Moving Condensor CleaningProduct Disposal Interval Every Three MonthsIf Service is Required Before Calling for ServiceReplacement Parts Troubleshooting GuideDESIGNED, Engineered and Assembled in WISCONSIN, USA
Top Page Image Contents