U-Line 1000 Door Alignment and Adjustment, Door Reversability, Reversing the door, Standard Doors

Page 14

7 Standard Doors

Door Alignment and Adjustment

Align and adjust the door if it is not level, or is not sealing properly. If the door is not sealed the unit may not cool properly, or excessive frost may form in the interior.

IMPORTANT

Properly aligned, the door’s gasket should be firmly in contact with the cabinet all the way around the door (no gaps). Carefully examine the door’s gasket to assure that it is firmly in contact with the cabinet. Also make sure the door gasket is not pinched on the hinge side of the door.

To align and adjust the door:

1.Loosen (do not remove) top and bottom hinge screws.

2.Align door squarely with cabinet.

3.Make sure gasket is firmly in contact with cabinet all the way around the door (no gaps).

4.Tighten bottom hinge screws.

5.Tighten top hinge screws.

Door Reversability

Location of the unit may make it desirable to mount the door on the opposite side of the cabinet.

Models with black and white doors are field-reversible.

Stainless steel models with glass doors without locks are field- reversible.

Stainless steel models without glass doors must be ordered right- or left-hand hinged.

Reversing the door

The Hinge hardware will be removed and reinstalled on the opposite side of the cabinet.

The hinge plate is flipped over when it is reinstalled on the opposite side of the cabinet.

 

 

 

 

 

 

 

 

 

 

 

 

Plastic

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Plastic

 

 

 

 

 

 

Plug Hole

 

 

 

 

 

 

Plug Hole

 

 

 

 

 

 

 

 

 

 

 

 

 

Right Side

Left Side

Door Swing

Door Swing

 

To reverse the door:

Remove grille:

Remove the grille see MAINTENANCE section of this guide.

Remove top hinge, and door:

1.Hold door to keep it from falling.

2.Remove top hinge from cabinet by removing three or four screws, depending on model.

3.Remove door by tilting forward and lifting door off bottom hinge.

4.Remove three or four plastic screw plugs from hinge holes on the opposite side. Reinstall into holes where the hinge was

removed. Ensure not to scratch cabinet.

Remove bottom hinge:

1.Remove bottom hinge from cabinet. Some models will have a gusset with two screws. Other models will have a plate with three screws.

2.Remove corresponding screws on opposite side of cabinet. On

12

U-Line Standard Door Alignment and Reversal

Page 13 Page 15
Image 14
Page 13 Page 15
Contents USE and Care Guide Introduction Read and save this Use and Care GuidePlease Record Your Model Information Table of Contents Safety Precautions Safety Alert DefinitionsGeneral Precautions Wine Captain Model Features All 1000 Series Models FeatureWine Captain Model and Beverage Center Features Beverage Center FeaturesControl Dial Air FlowInitial Startup Product OperationTo check the actual product temperature in the unit Adjusting AirTemperatureChecking Product Temperature Interior LightingLine Wine Guide Looking Behind the LabelWine Selections Suggestions Red WinesIdeal Wine Storage Considerations Terminology DescriptionDo not remove the track rails from the cabinet Wine Rack Removal and InstallationWine Stocking Recommendation Wood Trim Finishing Staining and final finish applicationLeveling Lightbulb ReplacementMaintenance Installing the grille Removing and Installing Door ShelvesRemoving and Installing Grille 15 & 29 ModelsReversing the door Door Alignment and AdjustmentDoor Reversability Standard DoorsInstall top hinge, and door Install bottom hingePrepare door for reinstallation For black or white doors Prepare door for reinstallationCleaning Exterior CleaningInterior Cleaning DefrostingProduct Disposal Condensor CleaningStorage, Vacation and Moving Interval Every Six MonthsReplacement Parts Before Calling for ServiceIf Service is Required Troubleshooting GuideLine Corporation Limited Warranty LINE.COM
Top Page Image Contents