U-Line 1000 manual Install bottom hinge, Prepare door for reinstallation For black or white doors

Page 15

1

Install bottom hinge:

1.If you have a plate hinge, reorient the pivot screw so it protrudes the opposite direction form the hinge. Remove the pivot screw from the hinge. Turn the plate over and reinstall the screw.

2.Align hinge outer edge with cabinet. For models with a plate hinge, the flat edge of the hinge alignes with the outer edge of the cabinet.

Install two or three screws, depending on model. Replace nuts if used.

Prepare door for reinstallation:

For black or white doors:

1.Remove plastic hole plug from top of door handle and reinstall on opposite side.

2.Remove plastic hinge bushing on bottom of door and reinstall on opposite side. Clean out bushing hole in door bottom with a screwdriver if necessary.

 

3

 

 

 

4

 

 

2

 

Install top hinge, and door:

1

1.

Reorient the pivot screw so it protrudes the opposite

 

 

 

 

direction from the hinge. Remove the pivot screw from the

 

 

 

hinge. Turn the plate over and reinstall the screw.

 

 

2.

Hold door to keep it from falling.

 

Prepare door for reinstallation:

3.

Lift the door on to the bottom hinge.

 

For stainless steel models with glass doors:

4.

Align flat edge of the hinge with the outer edge of the unit.

 

3. Stainless glass doors are flipped upside down to be reversed.

5.

Install three or four screws, depending on model.

 

4. Lay the door on it’s side. Remove the plastic hole plug (1) and

Align and adjust the door:

 

install in the corner opposite of where it was removed.

1.

Align and adjust the door, see DOOR ALIGNMENT AND

 

 

 

5. Remove the plastic hinge bushing (2) and install in the corner

 

ADJUSTMENT above.

 

opposite of where it was removed.

Install grille:

 

 

6. Remove the U-Line nameplate (3) from door. This will reveal

Install the grille, see MAINTENANCE section of this guide.

mounting holes for the door actuator bracket.

 

7.Remove door actuator (4) from door. Be sure to only remove the two screws holding the actuator to the door. Reinstall the actuator (4) on the opposite end of the door where the nameplate was removed.

8.Install new nameplate where the actuator assembly was removed.

9.Install screws into holes on opposite side, where the hinge was removed. Replace nuts if used.

U-Line Standrd Door Alignment and Reversal

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents USE and Care Guide Read and save this Use and Care Guide Please Record Your Model InformationIntroduction Table of Contents Safety Alert Definitions General PrecautionsSafety Precautions Beverage Center Features All 1000 Series Models FeatureWine Captain Model and Beverage Center Features Wine Captain Model FeaturesProduct Operation Air FlowInitial Startup Control DialInterior Lighting Adjusting AirTemperatureChecking Product Temperature To check the actual product temperature in the unitRed Wines Looking Behind the LabelWine Selections Suggestions Line Wine GuideTerminology Description Ideal Wine Storage ConsiderationsWine Rack Removal and Installation Wine Stocking RecommendationDo not remove the track rails from the cabinet Staining and final finish application Wood Trim Finishing Lightbulb Replacement Maintenance Leveling 15 & 29 Models Removing and Installing Door ShelvesRemoving and Installing Grille Installing the grilleStandard Doors Door Alignment and AdjustmentDoor Reversability Reversing the doorPrepare door for reinstallation Install bottom hingePrepare door for reinstallation For black or white doors Install top hinge, and doorDefrosting Exterior CleaningInterior Cleaning CleaningInterval Every Six Months Condensor CleaningStorage, Vacation and Moving Product DisposalTroubleshooting Guide Before Calling for ServiceIf Service is Required Replacement PartsLine Corporation Limited Warranty LINE.COM
Top Page Image Contents