Taylor C709, C717 manual Managers Menu

Page 26

A soft lock can also occur any time during operation when the hopper or freezing cylinder temperature rises above 59°F (15°C), the temperature rises and remains above 45°F(7°C) for more than one hour, or the temperature rises and remains above 41°F(5°C) for more than four hours.

If a PRODUCT OVER TEMPERATURE condition occurs during operation, the following screen will appear.

PRODUCT OVER TEMP

>HEAT FOR HEAT CYCLE WASH TO BRUSH CLEAN

When one of these messages appears, automatic freezer operation cannot take place until the freezer is disassembled and brush cleaned, or has completed a heat treatment cycle.

Once the freezer is unlocked by starting a heat treatment cycle the HEAT symbol will illuminate and the following message will be displayed on the screen.

DO NOT DRAW

If BRUSH CLEAN is selected to clear the lockout by brush cleaning the machine, the FREEZER LOCKED message will remain on the display until the brush clean requirements are fulfilled. The freezer must be disassembled in order to activate the five minute timer on the display screen. Once the timer counts down to zero, the lockout is cleared.

FREEZER LOCKED

130228

To restore the message that identified the reason for the soft lock, turn the power switch OFF for five seconds, and then return the power switch to the ON position. The original message with the reason for the soft lock will be displayed.

HEAT TREAT FAILURE

REASON

>HEAT FOR HEAT CYCLE WASH TO BRUSH CLEAN

Note: A record of Heat Cycle Data and Lock Out History can be found in the Manager's Menu.

Manager's Menu

The Manager's Menu is used to enter the operator function displays. To access the Menu, touch the center of the CONE symbol on the control panel. The arrow symbols, the SEL symbol and the CONE symbol will be lit when the ACCESS CODE screen is displayed.

Figure 10

In the Menu program, the arrow symbols and the SEL symbol will function as menu keys.

SUP ARROW - increases the value above the cursor and is used to scroll upward in text displays.

SDOWN ARROW - decreases the value above the cursor and is used to scroll downward in text displays.

SSEL - advances the cursor position to the right and is used to select menu options.

Important: To the Operator

22

Models C709 & C717

 

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operators Manual Model C709 & C717 Heat Treatment Soft Serve FreezersInformation found on the data label Table of Contents Table of Contents Section Installer SafetyModels C709 & C717 To the Installer Site PreparationElectrical Connections To the Installer Models C709 & C717Water Connections Water Cooled Units OnlyBeater Rotation RefrigerantTo the Operator Models C709 & C717 Compressor Warranty DisclaimerSection To the Operator Section Safety Models C709 & C717 SafetySafety Models C709 & C717 Models C709 & C717 Operator Parts Identification Operator Parts IdentificationModel C709 Model C709 Single Spout Door and Beater Assembly Operator Parts Identification Models C709 & C717Model C717 Model C717 Exploded View Parts Identification Model C717 Three Spout Door and Beater Assembly Feed Tube Assembly Accessories Brushes Section Important To the Operator Models C709 & C717 Important To the OperatorIndicator Lights Symbol DefinitionsPower Switch Standby SymbolReset Mechanism Wash SymbolAuto Symbol Adjustable Draw HandlePower Up Memory Initializing Operating Screen DescriptionsInternational Models Only Power Switch onPower Switch OFF Heat Cycle DataHardlock Freezer LocksHeat Cycle Soft Lock Auto Heat TimeManagers Menu Exit From Menu Entering Access CodeManager Menu Options Servings CounterSet Clock Auto Heat Time Auto Start TimeMix Level Audible Standby ModeFault Description Fault History Lockout HistoryHeat Cycle Summary Heat Cycle DataHeat Time Failure Current Conditions Net Service PinSystem Information Models C709 & C717 Operating Procedures Section Operating ProceduresAssembly Repeat these steps for the other side of the C717 Freezer Door AssemblyModel C709 Freezer Door Assembly Model C709 Freezer Door Assembly Contd Step Operating Procedures Models C709 & C717 Model C717 Freezer Door AssemblyModel C709 Freezer Door Assembly Contd Lubricate the gaskets or bearingsStep Feed Tube Assembly Model C717 Freezer Door Assembly Contd StepSanitizing Repeat Steps 1 through 4 for the other side of the C717Place the power switch in the on position Priming Daily Closing Procedures This procedure must be performed once dailyDaily Opening Procedures Set-Up Complete The FollowingManual Brush Cleaning Draining Product From The Freezing Cylinder RinsingHopper Cleaning DisassemblyBrush Cleaning Repeat these steps for the other side of the C717 StepTroubleshooting Bacterial Count Important Operator ChecklistDuring Brush Cleaning and Sanitizing Regular Maintenance ChecksModels C709 & C717 Important Operator Checklist Winter StorageSection Troubleshooting Guide Troubleshooting Guide Models C709 & C717Models C709 & C717 Troubleshooting Guide Problem Probable Cause Remedy Problem Probable Cause Remedy Parts Replacement Schedule Parts Replacement Schedule Models C709 & C717Limited Warranty on Equipment Limited Warranty on Equipment Models C709 & C717 Models C709 & C717 Limited Warranty on Parts Limited Warranty on PartsParts Warranty Class Code or Part Limited Warranty Period Limited Warranty on Parts Models C709 & C717 Taylor Company Switch HOT GAS Interface Board Solenoid Power TransformerPower OFF Limit SwitchJP7 Jumper Installed Disables Reset Rtck Relay Power TransformerSwitch Overload Temperature CheckTo Hook UP a Compressor Using a Start and RUN Additional Draw SwitchDraw Start CAP Switch RUN Capacitor Start Capacitor WHT BLK Line Filter Spinner Motor WiringOverload Barrel Switch Compressor Suction Power OFF Switch DpdtDraw OUT Intfc PCB A. J5 Switch Limit Switch Solenoid High PressureRED WHT Blue GE/RBC/MARATHON Beater Motor WiringBlack T1 T1 or Blue Internal T8 or RED Internal BLU REDGRN/YEL Ribbon Cable WHT WHT WHTAgitator Motor WHT/GRA LIVBLK WHT RED ORN USE T3 and L3 When CPAdditional Draw Switch For Flavorburst BLK Probe YEL BLKGRN/YEL PRP Draw SwitchWHT RED ORN AJ1

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.
Top Page Image Contents