Taylor C717, C709 manual Soft Lock, Auto Heat Time

Page 25

Touching the SEL symbol will display the following screen.

FREEZER LOCKED

2.The following screen will display if there has been a thermistor failure (freezing cylinder or hopper) during the heat treatment process.

SYSTEM FAULT

FREEZER LOCKED

SERVICE REQ'D

>WASH TO BRUSH CLEAN

Touching the SEL symbol will indicate which thermistor caused the Hard Lock.

HOPPER THERM BAD

FREEZER LOCKED

If the machine has hard locked and an attempt is made to enter AUTO, the machine will enter the STANDBY mode and display the following message.

FREEZER LOCKED

To restore the message that identified the reason for the hard lock, turn the power switch OFF for five seconds and then return the power switch to the ON position. The original message with the reason for the Hard Lock will be displayed.

The FREEZER LOCKED message will remain on the display until the brush clean requirements are fulfilled. The freezer must be disassembled in order to activate the five minute timer on the display screen. Once the timer counts down to zero, the lockout is cleared.

Soft Lock

If a heat treatment cycle has not been initiated within the last 24 hours, a soft lock failure will occur. A soft lock allows the operator to correct the cause of the soft lock. The operator has the option of either starting another heat cycle or brush cleaning the machine. When a soft lock occurs, the machine will go into the STANDBY mode. The following message is displayed on the screen. The reason for the soft lock is indicated on the second line.

NO HEAT CYCLE START

REASON

>HEAT FOR HEAT CYCLE WASH TO BRUSH CLEAN

If the reason for the soft lock has been corrected, selecting HEAT CYCLE initiates a Heat Cycle immediately. Selecting BRUSH CLEAN when the previous message is displayed will hard lock the machine and brush cleaning will be necessary.

Following are the variable messages for soft lock failures that appear on the second line of the screen.

POWER SWITCH OFF

Power switch was in the

 

OFF position.

 

 

MIX OUT PRESENT

There was a mix out

 

condition present.

 

 

AUTO OR STANDBY

The machine was not in

OFF

the AUTO or STANDBY

 

mode.

 

 

NO HEAT CYCLE

A heat treatment cycle

TRIED

was not attempted in

 

the last 24 hours.

 

(AUTO HEAT TIME

 

was advanced or a

 

power loss was experi-

 

enced at the time the

 

cycle was to occur.)

 

 

If the following screen appears, a soft lock has occurred during the heat treatment cycle.

HEAT TREAT FAILURE

FREEZER LOCKED

>HEAT FOR HEAT CYCLE WASH TO BRUSH CLEAN

Models C709 & C717

21

Important: To the Operator

 

 

 

Image 25
Contents Model C709 & C717 Heat Treatment Soft Serve Freezers Operators ManualInformation found on the data label Table of Contents Table of Contents Models C709 & C717 To the Installer Installer SafetySection Site PreparationWater Connections To the Installer Models C709 & C717Electrical Connections Water Cooled Units OnlyRefrigerant Beater RotationSection To the Operator Compressor Warranty DisclaimerTo the Operator Models C709 & C717 Models C709 & C717 Safety Section SafetySafety Models C709 & C717 Model C709 Operator Parts IdentificationModels C709 & C717 Operator Parts Identification Operator Parts Identification Models C709 & C717 Model C709 Single Spout Door and Beater AssemblyModel C717 Model C717 Exploded View Parts Identification Model C717 Three Spout Door and Beater Assembly Feed Tube Assembly Accessories Brushes Models C709 & C717 Important To the Operator Section Important To the OperatorPower Switch Symbol DefinitionsIndicator Lights Standby SymbolAuto Symbol Wash SymbolReset Mechanism Adjustable Draw HandleOperating Screen Descriptions Power Up Memory InitializingPower Switch OFF Power Switch onInternational Models Only Heat Cycle DataHeat Cycle Freezer LocksHardlock Auto Heat Time Soft LockManagers Menu Manager Menu Options Entering Access CodeExit From Menu Servings CounterSet Clock Auto Start Time Auto Heat TimeFault Description Standby ModeMix Level Audible Lockout History Fault HistoryHeat Cycle Data Heat Cycle SummaryHeat Time Failure System Information Net Service PinCurrent Conditions Assembly Section Operating ProceduresModels C709 & C717 Operating Procedures Model C709 Freezer Door Assembly Freezer Door AssemblyRepeat these steps for the other side of the C717 Model C709 Freezer Door Assembly Contd Step Model C709 Freezer Door Assembly Contd Model C717 Freezer Door AssemblyOperating Procedures Models C709 & C717 Lubricate the gaskets or bearingsStep Model C717 Freezer Door Assembly Contd Step Feed Tube AssemblyRepeat Steps 1 through 4 for the other side of the C717 SanitizingPlace the power switch in the on position Priming This procedure must be performed once daily Daily Closing ProceduresSet-Up Complete The Following Daily Opening ProceduresManual Brush Cleaning Rinsing Draining Product From The Freezing CylinderDisassembly Hopper CleaningRepeat these steps for the other side of the C717 Step Brush CleaningDuring Brush Cleaning and Sanitizing Important Operator ChecklistTroubleshooting Bacterial Count Regular Maintenance ChecksWinter Storage Models C709 & C717 Important Operator ChecklistTroubleshooting Guide Models C709 & C717 Section Troubleshooting GuideModels C709 & C717 Troubleshooting Guide Problem Probable Cause Remedy Problem Probable Cause Remedy Parts Replacement Schedule Models C709 & C717 Parts Replacement ScheduleLimited Warranty on Equipment Limited Warranty on Equipment Models C709 & C717 Parts Warranty Class Code or Part Limited Warranty Period Limited Warranty on PartsModels C709 & C717 Limited Warranty on Parts Limited Warranty on Parts Models C709 & C717 Taylor Company Power OFF HOT GAS Interface Board Solenoid Power TransformerSwitch Limit SwitchSwitch Overload Relay Power TransformerJP7 Jumper Installed Disables Reset Rtck Temperature CheckDraw Start CAP Switch RUN Capacitor Start Capacitor Additional Draw SwitchTo Hook UP a Compressor Using a Start and RUN WHT BLK Line Filter Spinner Motor WiringDraw OUT Intfc PCB A. J5 Switch Power OFF Switch DpdtOverload Barrel Switch Compressor Suction Limit Switch Solenoid High PressureBlack T1 T1 or Blue Internal T8 or RED Internal WHT Blue GE/RBC/MARATHON Beater Motor WiringRED BLU REDAgitator Motor WHT WHTGRN/YEL Ribbon Cable WHT WHT/GRA LIVAdditional Draw Switch For Flavorburst BLK USE T3 and L3 When CPBLK WHT RED ORN Probe YEL BLKWHT RED ORN Draw SwitchGRN/YEL PRP AJ1

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.