Taylor C709, C717 manual Daily Closing Procedures, This procedure must be performed once daily

Page 44

Daily Closing Procedures

This procedure must be performed once daily!

The function of the Heat Treatment Cycle is to destroy bacteria by raising the temperature of the mix in the freezing cylinder and the hopper to a specified temperature for a specified period of time, and then bringing the temperature back down low enough to retard spoilage.

The Heat Treatment Cycle will start at the time designated in the Auto Heat Time.

IMPORTANT: The level of mix in the mix hopper(s) must be up to the fill line on the agitator paddle(s). (The mix low light must not be on.) Note: If the BRUSH CLEAN COUNTER display has counted down to one day, do not add mix. The machine must be disassembled and brush cleaned within 24 hours.

The freezer must be in the AUTO (AUTO symbol illuminated) or in the STANDBY mode (STANDBY

symbol illuminated) before the HEAT cycle may be started.

Step 1

Remove the hopper cover(s), drip pan(s), front drip tray, and the splash shield. Take them to the sink for cleaning and sanitizing.

MAKE SURE YOUR HANDS ARE CLEAN AND SANITIZED BEFORE PERFORMING THESE NEXT STEPS.

Step 2

Remove the air orifice(s), the feed tube assembly(lies), and the agitator(s) from the mix hopper(s). Take these parts to the sink for cleaning and sanitizing.

Step 3

Rinse these parts in cool, clean water.

140722

Step 4

Prepare a small amount of an approved 100 PPM cleaning/sanitizing solution (examples: Kay-5® or Stera-Sheen®). USE WARM WATER AND FOLLOW THE MANUFACTURER'S SPECIFICATIONS. Brush clean the parts.

Step 5

Place the front drip tray, splash shield, and air orifice(s) on a clean, dry surface to air-dry overnight or until the heating cycle is complete.

Step 6

Prepare a small amount of an approved 100 PPM cleaning/sanitizing solution (examples: Kay-5® or Stera-Sheen®). USE WARM WATER AND FOLLOW THE MANUFACTURER'S SPECIFICATIONS. Sanitize the drip pans, feed tube assembly(ies), agitator(s) and hopper cover(s).

Step 7

Install the agitator(s) back onto the agitator drive shaft housing(s).

CAUTION: Be sure agitator(s) are installed and switch is in the AUTO or STANDBY mode or the unit will not have a successful heat cycle.

Step 8

Install the feed tube assembly(ies). Lift and turn the inner feed tube of each assembled feed tube so the pin rests on top of the outer feed tube. This will close the hole in the assembled feed tubes, preventing mix in the hopper(s) from entering the freezing cylinder(s) during the Heating and Standby process.

Figure 44

Operating Procedures

40

Models C709 & C717

 

 

 

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Operators Manual Model C709 & C717 Heat Treatment Soft Serve FreezersInformation found on the data label Table of Contents Table of Contents Installer Safety Models C709 & C717 To the InstallerSection Site PreparationTo the Installer Models C709 & C717 Water ConnectionsElectrical Connections Water Cooled Units OnlyBeater Rotation RefrigerantTo the Operator Models C709 & C717 Compressor Warranty DisclaimerSection To the Operator Section Safety Models C709 & C717 SafetySafety Models C709 & C717 Models C709 & C717 Operator Parts Identification Operator Parts IdentificationModel C709 Model C709 Single Spout Door and Beater Assembly Operator Parts Identification Models C709 & C717Model C717 Model C717 Exploded View Parts Identification Model C717 Three Spout Door and Beater Assembly Feed Tube Assembly Accessories Brushes Section Important To the Operator Models C709 & C717 Important To the OperatorSymbol Definitions Power SwitchIndicator Lights Standby SymbolWash Symbol Auto SymbolReset Mechanism Adjustable Draw HandlePower Up Memory Initializing Operating Screen DescriptionsPower Switch on Power Switch OFFInternational Models Only Heat Cycle DataHardlock Freezer LocksHeat Cycle Soft Lock Auto Heat TimeManagers Menu Entering Access Code Manager Menu OptionsExit From Menu Servings CounterSet Clock Auto Heat Time Auto Start TimeMix Level Audible Standby ModeFault Description Fault History Lockout HistoryHeat Cycle Summary Heat Cycle DataHeat Time Failure Current Conditions Net Service PinSystem Information Models C709 & C717 Operating Procedures Section Operating ProceduresAssembly Repeat these steps for the other side of the C717 Freezer Door AssemblyModel C709 Freezer Door Assembly Model C709 Freezer Door Assembly Contd Step Model C717 Freezer Door Assembly Model C709 Freezer Door Assembly ContdOperating Procedures Models C709 & C717 Lubricate the gaskets or bearingsStep Feed Tube Assembly Model C717 Freezer Door Assembly Contd StepSanitizing Repeat Steps 1 through 4 for the other side of the C717Place the power switch in the on position Priming Daily Closing Procedures This procedure must be performed once dailyDaily Opening Procedures Set-Up Complete The FollowingManual Brush Cleaning Draining Product From The Freezing Cylinder RinsingHopper Cleaning DisassemblyBrush Cleaning Repeat these steps for the other side of the C717 StepImportant Operator Checklist During Brush Cleaning and SanitizingTroubleshooting Bacterial Count Regular Maintenance ChecksModels C709 & C717 Important Operator Checklist Winter StorageSection Troubleshooting Guide Troubleshooting Guide Models C709 & C717Models C709 & C717 Troubleshooting Guide Problem Probable Cause Remedy Problem Probable Cause Remedy Parts Replacement Schedule Parts Replacement Schedule Models C709 & C717Limited Warranty on Equipment Limited Warranty on Equipment Models C709 & C717 Models C709 & C717 Limited Warranty on Parts Limited Warranty on PartsParts Warranty Class Code or Part Limited Warranty Period Limited Warranty on Parts Models C709 & C717 Taylor Company HOT GAS Interface Board Solenoid Power Transformer Power OFFSwitch Limit SwitchRelay Power Transformer Switch OverloadJP7 Jumper Installed Disables Reset Rtck Temperature CheckAdditional Draw Switch Draw Start CAP Switch RUN Capacitor Start CapacitorTo Hook UP a Compressor Using a Start and RUN WHT BLK Line Filter Spinner Motor WiringPower OFF Switch Dpdt Draw OUT Intfc PCB A. J5 SwitchOverload Barrel Switch Compressor Suction Limit Switch Solenoid High PressureWHT Blue GE/RBC/MARATHON Beater Motor Wiring Black T1 T1 or Blue Internal T8 or RED InternalRED BLU REDWHT WHT Agitator MotorGRN/YEL Ribbon Cable WHT WHT/GRA LIVUSE T3 and L3 When CP Additional Draw Switch For Flavorburst BLKBLK WHT RED ORN Probe YEL BLKDraw Switch WHT RED ORNGRN/YEL PRP AJ1

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.
Top Page Image Contents