Taylor C717, C709 manual Beater Rotation, Refrigerant

Page 7

Beater Rotation

Beater rotation must be clockwise as viewed looking into the freezing cylinder.

Note: The following procedures should be performed by a trained service technician.

To correct rotation on a three-phase unit, interchange any two incoming power supply lines at freezer main terminal block only.

To correct rotation on a single-phase unit, change the leads inside the beater motor. (Follow diagram printed on motor.)

Electrical connections are made directly to the terminal block provided behind the lower front panel.

Refrigerant

In consideration of our environment, Taylor proudly uses only earth friendly HFC refrigerants. The HFC refrigerant used in this unit is R404A. This refrigerant is generally considered non-toxic and non-flammable, with an Ozone Depleting Potential (ODP) of zero (0).

However, any gas under pressure is potentially hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with liquid. Filling the cylinder to approximately 80% will allow for normal expansion.

Use only R404A refrigerant that conforms to the AHRI standard 700 specification. The use of any other refrigerant may expose users and operators to unexpected safety hazards.

Refrigerant liquid sprayed onto the skin may cause serious damage to tissue. Keep eyes and skin protected. If refrigerant burns should occur, flush immediately with cold water. If burns are severe, apply ice packs and contact a physician immediately.

Taylor reminds technicians to be cautious of government laws regarding refrigerant recovery, recycling, and reclaiming systems. If you have any questions regarding these laws, please contact the factory Service Department.

WARNING: R404A refrigerant used in conjunction with polyolester oils is extremely moisture absorbent. When opening a refrigeration system, the maximum time the system is open must not exceed 15 minutes. Cap all open tubing to prevent humid air or water from being absorbed by the oil.

130819

Models C709 & C717

3

To the Installer

 

 

 

Image 7
Contents Model C709 & C717 Heat Treatment Soft Serve Freezers Operators ManualInformation found on the data label Table of Contents Table of Contents Site Preparation Installer SafetyModels C709 & C717 To the Installer SectionWater Cooled Units Only To the Installer Models C709 & C717Water Connections Electrical ConnectionsRefrigerant Beater RotationSection To the Operator Compressor Warranty DisclaimerTo the Operator Models C709 & C717 Models C709 & C717 Safety Section SafetySafety Models C709 & C717 Model C709 Operator Parts IdentificationModels C709 & C717 Operator Parts Identification Operator Parts Identification Models C709 & C717 Model C709 Single Spout Door and Beater AssemblyModel C717 Model C717 Exploded View Parts Identification Model C717 Three Spout Door and Beater Assembly Feed Tube Assembly Accessories Brushes Models C709 & C717 Important To the Operator Section Important To the OperatorStandby Symbol Symbol DefinitionsPower Switch Indicator LightsAdjustable Draw Handle Wash SymbolAuto Symbol Reset MechanismOperating Screen Descriptions Power Up Memory InitializingHeat Cycle Data Power Switch onPower Switch OFF International Models OnlyHeat Cycle Freezer LocksHardlock Auto Heat Time Soft LockManagers Menu Servings Counter Entering Access CodeManager Menu Options Exit From MenuSet Clock Auto Start Time Auto Heat TimeFault Description Standby ModeMix Level Audible Lockout History Fault HistoryHeat Cycle Data Heat Cycle SummaryHeat Time Failure System Information Net Service PinCurrent Conditions Assembly Section Operating ProceduresModels C709 & C717 Operating Procedures Model C709 Freezer Door Assembly Freezer Door AssemblyRepeat these steps for the other side of the C717 Model C709 Freezer Door Assembly Contd Step Lubricate the gaskets or bearings Model C717 Freezer Door AssemblyModel C709 Freezer Door Assembly Contd Operating Procedures Models C709 & C717Step Model C717 Freezer Door Assembly Contd Step Feed Tube AssemblyRepeat Steps 1 through 4 for the other side of the C717 SanitizingPlace the power switch in the on position Priming This procedure must be performed once daily Daily Closing ProceduresSet-Up Complete The Following Daily Opening ProceduresManual Brush Cleaning Rinsing Draining Product From The Freezing CylinderDisassembly Hopper CleaningRepeat these steps for the other side of the C717 Step Brush CleaningRegular Maintenance Checks Important Operator ChecklistDuring Brush Cleaning and Sanitizing Troubleshooting Bacterial CountWinter Storage Models C709 & C717 Important Operator ChecklistTroubleshooting Guide Models C709 & C717 Section Troubleshooting GuideModels C709 & C717 Troubleshooting Guide Problem Probable Cause Remedy Problem Probable Cause Remedy Parts Replacement Schedule Models C709 & C717 Parts Replacement ScheduleLimited Warranty on Equipment Limited Warranty on Equipment Models C709 & C717 Parts Warranty Class Code or Part Limited Warranty Period Limited Warranty on PartsModels C709 & C717 Limited Warranty on Parts Limited Warranty on Parts Models C709 & C717 Taylor Company Limit Switch HOT GAS Interface Board Solenoid Power TransformerPower OFF SwitchTemperature Check Relay Power TransformerSwitch Overload JP7 Jumper Installed Disables Reset RtckWHT BLK Line Filter Spinner Motor Wiring Additional Draw SwitchDraw Start CAP Switch RUN Capacitor Start Capacitor To Hook UP a Compressor Using a Start and RUNLimit Switch Solenoid High Pressure Power OFF Switch DpdtDraw OUT Intfc PCB A. J5 Switch Overload Barrel Switch Compressor SuctionBLU RED WHT Blue GE/RBC/MARATHON Beater Motor WiringBlack T1 T1 or Blue Internal T8 or RED Internal REDWHT/GRA LIV WHT WHTAgitator Motor GRN/YEL Ribbon Cable WHTProbe YEL BLK USE T3 and L3 When CPAdditional Draw Switch For Flavorburst BLK BLK WHT RED ORNAJ1 Draw SwitchWHT RED ORN GRN/YEL PRP

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.