Taylor manual Winter Storage, Models C709 & C717 Important Operator Checklist

Page 51

j7. If your machine is equipped with an auxiliary refrigeration system, check the auxiliary condenser for accumulation of dirt and lint. Dirty condensers will reduce the refrigeration capacity of the mix hopper. Condensers must be cleaned monthly with a soft brush. Never use screwdrivers or other metal probes to clean between the fins.

WARNING! Always disconnect electrical power prior to cleaning the condenser. Failure to follow this instruction may result in electrocution.

j8. If your machine is water cooled, check the water lines for kinks or leaks. Kinks can occur when the machine is moved back and forth for cleaning or maintenance purposes. Deteriorated or cracked water lines should be replaced only by an authorized Taylor distributor.

Winter Storage

If the place of business is to be closed during the winter months, it is important to protect the freezer by following certain precautions, particularly if the building is subject to freezing conditions.

Disconnect the freezer from the main power source to prevent possible electrical damage.

On water cooled freezers, disconnect the water supply. Relieve pressure on the spring in the water valve. Use air pressure on the outlet side to blow out any water remaining in the condenser. This is extremely important. Failure to follow this procedure may cause severe and costly damage to the refrigeration system.

Your local Taylor Distributor can perform this winter storage service for you.

Wrap detachable parts of the freezer such as beater, blades, drive shaft, and freezer door, and place them in a protected dry place. Rubber trim parts and gaskets can be protected by wrapping them with moisture-proof paper. All parts should be thoroughly cleaned of dried mix or lubrication which attract mice and other vermin.

It is recommended that an authorized service technician perform winter storage draining, to insure all water has been removed. This will guard against freezing and rupturing of the components.

080128

Models C709 & C717

47

Important: Operator Checklist

 

 

 

Image 51
Contents Model C709 & C717 Heat Treatment Soft Serve Freezers Operators ManualInformation found on the data label Table of Contents Table of Contents Site Preparation Installer SafetyModels C709 & C717 To the Installer SectionWater Cooled Units Only To the Installer Models C709 & C717Water Connections Electrical ConnectionsRefrigerant Beater RotationCompressor Warranty Disclaimer Section To the OperatorTo the Operator Models C709 & C717 Models C709 & C717 Safety Section SafetySafety Models C709 & C717 Operator Parts Identification Model C709Models C709 & C717 Operator Parts Identification Operator Parts Identification Models C709 & C717 Model C709 Single Spout Door and Beater AssemblyModel C717 Model C717 Exploded View Parts Identification Model C717 Three Spout Door and Beater Assembly Feed Tube Assembly Accessories Brushes Models C709 & C717 Important To the Operator Section Important To the OperatorStandby Symbol Symbol DefinitionsPower Switch Indicator LightsAdjustable Draw Handle Wash SymbolAuto Symbol Reset MechanismOperating Screen Descriptions Power Up Memory InitializingHeat Cycle Data Power Switch onPower Switch OFF International Models OnlyFreezer Locks Heat CycleHardlock Auto Heat Time Soft LockManagers Menu Servings Counter Entering Access CodeManager Menu Options Exit From MenuSet Clock Auto Start Time Auto Heat TimeStandby Mode Fault DescriptionMix Level Audible Lockout History Fault HistoryHeat Cycle Data Heat Cycle SummaryHeat Time Failure Net Service Pin System InformationCurrent Conditions Section Operating Procedures AssemblyModels C709 & C717 Operating Procedures Freezer Door Assembly Model C709 Freezer Door AssemblyRepeat these steps for the other side of the C717 Model C709 Freezer Door Assembly Contd Step Lubricate the gaskets or bearings Model C717 Freezer Door AssemblyModel C709 Freezer Door Assembly Contd Operating Procedures Models C709 & C717Step Model C717 Freezer Door Assembly Contd Step Feed Tube AssemblyRepeat Steps 1 through 4 for the other side of the C717 SanitizingPlace the power switch in the on position Priming This procedure must be performed once daily Daily Closing ProceduresSet-Up Complete The Following Daily Opening ProceduresManual Brush Cleaning Rinsing Draining Product From The Freezing CylinderDisassembly Hopper CleaningRepeat these steps for the other side of the C717 Step Brush CleaningRegular Maintenance Checks Important Operator ChecklistDuring Brush Cleaning and Sanitizing Troubleshooting Bacterial CountWinter Storage Models C709 & C717 Important Operator ChecklistTroubleshooting Guide Models C709 & C717 Section Troubleshooting GuideModels C709 & C717 Troubleshooting Guide Problem Probable Cause Remedy Problem Probable Cause Remedy Parts Replacement Schedule Models C709 & C717 Parts Replacement ScheduleLimited Warranty on Equipment Limited Warranty on Equipment Models C709 & C717 Limited Warranty on Parts Parts Warranty Class Code or Part Limited Warranty PeriodModels C709 & C717 Limited Warranty on Parts Limited Warranty on Parts Models C709 & C717 Taylor Company Limit Switch HOT GAS Interface Board Solenoid Power TransformerPower OFF SwitchTemperature Check Relay Power TransformerSwitch Overload JP7 Jumper Installed Disables Reset RtckWHT BLK Line Filter Spinner Motor Wiring Additional Draw SwitchDraw Start CAP Switch RUN Capacitor Start Capacitor To Hook UP a Compressor Using a Start and RUNLimit Switch Solenoid High Pressure Power OFF Switch DpdtDraw OUT Intfc PCB A. J5 Switch Overload Barrel Switch Compressor SuctionBLU RED WHT Blue GE/RBC/MARATHON Beater Motor WiringBlack T1 T1 or Blue Internal T8 or RED Internal REDWHT/GRA LIV WHT WHTAgitator Motor GRN/YEL Ribbon Cable WHTProbe YEL BLK USE T3 and L3 When CPAdditional Draw Switch For Flavorburst BLK BLK WHT RED ORNAJ1 Draw SwitchWHT RED ORN GRN/YEL PRP

C717, C709 specifications

Taylor C709 and C717 are two outstanding models from the renowned Taylor Guitars, each designed to cater to the discerning tastes of musicians looking for exceptional playability, sound quality, and craftsmanship.

The Taylor C709 is known for its remarkable tonal balance and projection. Constructed with a solid Sitka spruce top, it delivers a bright, clear sound that enhances the overall musicality of the instrument. The back and sides of the C709 are crafted from layered sapele, which not only adds to the visual appeal but also contributes to a warm, resonant voice. This model features a Grand Symphony body shape, known for producing a rich, full sound, making it an excellent choice for strumming and fingerpicking alike.

On the other hand, the Taylor C717 takes things a notch further with its unique design and features. It also boasts a solid Sitka spruce top, but pairs it with solid sapele back and sides, offering a more vibrant and dynamic tonal range. The Grand Pacific body shape of the C717 is specifically engineered for a vintage-inspired sound, making it perfect for players seeking warmth and depth. This model is designed to provide a pleasing balance between bass, midrange, and treble frequencies, ensuring a versatile performance suited for various styles.

Both models are equipped with the Taylor Expression System 2, a technologically advanced pickup system designed to capture the natural acoustics of the guitar. This feature makes it easier for musicians to amplify their sound without compromising the instrument's organic tone.

In terms of playability, both the C709 and C717 are built with a smooth mahogany neck and an ebony fingerboard, which provides a comfortable playing surface for intricate fingerwork and chords. The action is set to make playing effortless, whether you're a beginner or an experienced musician.

Aesthetically, Taylor has ensured that these guitars are as visually striking as they are sonically impressive. The glossy finish, elegant inlays, and overall craftsmanship make them showpieces worthy of attention on stage or in a personal collection.

In conclusion, the Taylor C709 and C717 models represent the perfect blend of innovation, tradition, and artistry, making them coveted instruments for players at all levels. With their superior tone, excellent playability, and stunning design, these guitars continue to uphold Taylor’s legacy of quality and excellence in the world of acoustic instruments.