Smeg STA4645U manual Troubleshooting, User Instructions

Page 16

5 TROUBLESHOOTING

USER INSTRUCTIONS

EN

5 TROUBLESHOOTING

The dishwasher can to signal a number of malfunctions by turning on various indicator lights, as described below (see following table):

	FAULT	DESCRIPTION
		Acquastop failure
	E1	The anti-ﬂooding system has tripped (only for models
	E1	ﬁtted with this feature). Activates in case of water leaks.
		ﬁtted with this feature). Activates in case of water leaks.
		Contact the technical assistance service.
		Water heating malfunction
	E3	The water is not	heated or is incorrectly heated.
	E3	Repeat the washing program; if the problem persists,
		Repeat the washing program; if the problem persists,
		contact the technical assistance service.
		Water temperature monitoring malfunction
		Interrupt the current program. Switch off the
	E4	dishwasher, switch it back on again, program a new
		cycle and press start. If the problem persists, contact
		the technical assistance service.
		Water intake malfunction
		The appliance does not take in water or does so
	E5	incorrectly. Make	sure the water connections are
	E5	correct, that the water supply tap is open and that the
		correct, that the water supply tap is open and that the
		ﬁlter is not clogged. If the problem persists, contact
		the technical assistance service.
		Water pump-out malfunction
		The appliance does not pump out the water or does
	E6	so incorrectly. Make sure the drain hose is not kinked
	E6	or crushed and that the siphon and ﬁlters are not
		or crushed and that the siphon and ﬁlters are not
		clogged. If the problem persists, contact the technical
		assistance service.
			Tab. 4-01
	Light off	Light on	Light ﬂashing

Rev 0.0

15

Image 16

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS INSTRUCTION MANUALCONTENTS CONTENTSPage 1 INTRODUCTION INTRODUCTIONNomenclature of ﬁgures and tables Symbols used in this manual see tab This symbol highlights general information and warnings TabUSER INSTRUCTIONS 2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Upper panel2.2 Setting the washing program and switching on and off USER INSTRUCTIONSETL SANITATION LISTED2.2.1 Switching on 2.2.2 Selecting and starting the program2.2.3 End of program Before starting a washing program, make sure that2.2.4 Interrupting a program 2.2.6 Canceling the current program2.2.5 Changing the current program 2.2.7 Options PROGRAM DELAY2.2.8 Switching off 2.3.1 Adjusting the water softener2.3 Additional functions 3., 4., 5., 0., 1Water hardness table see tab WATER HARDNESS3 ENERGY SAVING AND ENVIRONMENTAL RESPECT 4 REMOVING THE DISHES 5 TROUBLESHOOTING Alarms E1, E3, E4, immediately terminate the current program Contents Page This manual comprises the following sections Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. Following the cleaning instruc- tions provided here will keep dishwasher performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasherSymbols used in this manual see tab WARNINGS 2 IMPORTANT SAFETY INSTRUCTIONSave this instructions WARNINGS ONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC DISHWASHERS DO NOT INTRODUCE ANIMALS INTO THE DISHWASHER DO NOT LEAN AGAINST OR STAND ON THE DISHWASHER RACKSATTEMPT TO REPAIR THE APPLIANCE THE MANUFACTURER DECLINES ALL RESPONSIBIL- ITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPER- TY RESULTING FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS INSTALLATION INSTRUCTIONS 3 INSTALLATION AND HOOK-UPINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS adjust the water softening system add the regenerating salt 4 OPERATING INSTRUCTIONSadd the rinse-aid and detergent 4.1 Using the water softening system When using the dishwasher for the ﬁ rst time, in addition to the salt it is also necessary to add one liter of water to the container 4.2 Using the rinse-aid and detergent dispensers ED AS REQUIRED4.2.2 Adjusting the rinse-aid dispenser setting 4.2.1 Adding the rinse-aid4.2.3 Adding the detergent When a program with hot prewash is selected see program table in the “De- scription of Controls” manual, extra detergent must be placed in the cavity ref. A or B ﬁ g. 4-06, depending on models 4.3 General warnings and recommendations Items which are not dishwasher-safe MAKE SURE that the items being washed are dishwasher-safeDishes and objects in copper, tin, zinc or brass these tend to stain 4.4 Using the racks 4.4.1 Lower rack Con supporti fissiEsempi di caricamento Loading the lower rack see ﬁ gLoading examples 4.4.2 Cutlery basket see ﬁ g 4.4.3 Upper rack vedi ﬁ g. 4-12 Loading the upper rack vedi ﬁ g EsempiLoading caricamentoexamplesAdjusting the upper rack 5.1 General warnings and recommendations 5 CLEANING AND USER-MAINTENANCENEVER USE ABRASIVE AND/OR CORROSIVE DETERGENTS TO CLEAN THE APPLIANCE 5.3 Cleaning the spray arms 5.2 Cleaning the water intake ﬁlter only some modelsRemoving the spray arms USER INSTRUCTIONS 5.4 Cleaning the ﬁlter unit 5.5 General warnings and recommendations for correct maintenance 5.6 Troubleshooting minor problems If the dishes do not come out clean, check thatProlonged disuse Before starting the dishwasher after prolonged disuseIf the dishes show signs of streaking, staining, etc., check that If the dishes fail to dry or remain dull, check thatIf there are visible traces of rust inside the tank 6 TECHNICAL DATA SEE TAB CONTENTS ContentsPage 1 INTRODUCTION INTRODUCTIONNomenclature of ﬁgures and tables Symbols used in this manual see tab 2 SAFETY INFORMATION EDGE OF THE DOOR MUST NEVER BE REMOVEDTWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHER REPAIR THE APPLIANCEWARNINGS 3 INSTALLATION MATERIAL INSTALLATION INSTRUCTIONSB A D C F G I L3.1 Kit supplied with dishwasher models sta4645/sta87433.2 Kit supplied with dishwasher models pla8743 DIMENSIONS OF DISHWASHER See ﬁ g 5 INSTALLATION AND HOOK-UP Only for free-standing models5.1 Leveling 5.1.1 Mounting the feet only for some models5.1.2 Levelling the appliance 5.2 Connections FIRE HAZARD DO NOT COVER OR CRUSH THE CORD PLUG5.2.1 Connecting to the water supply 5.2.1.1 Connecting to the water tap Do not cut the inlet hose see ﬁ g 5.2.1.2 Connecting the drain hose Connecting to a drain MAX 100 cm3-59/64” min O4 cmConnecting to a “T” union of the drain circuit Available from any plumbing stockistConnecting to a waste disposal unit with an air gap Connecting to the air gap no waste disposal unit Connecting to a waste disposal unit no air gap A D C B5.2.2 Electrical connections and warnings Grounding instructions5.3.1 Installation procedure all models 5.3 CommissioningINSTALLATION INSTRUCTIONS 5.3.2 Procedure for mounting the door panel Mount the door panelsee ﬁ g Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm 25/32” see ﬁ g INSTALLATION INSTRUCTIONS 5.3.3 Procedure for mounting the door panel models pla8743INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5.3.4 Completion of installation all models Remove the adhesive band on the gasket see ﬁ g INSTALLATION INSTRUCTIONS 5.4 Testing 19 570 0074