Smeg STA4645U manual Leveling, Mounting the feet only for some models, Installation Instructions

Page 67

5.1Leveling

INSTALLATION INSTRUCTIONS

EN

•If the appliance is not in a niche and can therefore be accessed on one side, cover the door hinge area for safety reasons (cutting hazard). Covers are available as accessories from specialized retailers or from the Technical Service Centre.

•To build in the dishwasher, purchase the relative kit from specialized retail- ers or from the Technical Service Centre.

5.1Leveling

5.1.1Mounting the feet (only for some models)

Turn the appliance upside-down (see ﬁ g. 5-01).

Tighten the nut (see ref. A ﬁ g. 5-01) onto the threaded pin (see ref. B ﬁ g. 5-01) of the foot and then ﬁ t the supplied washer; do this on both feet.

Screw the feet onto the appliance until the washers touch the base; the two feet must be manually adjusted to the same height to prevent excessive diffe- rences in height between one foot and the other.

Put the appliance back on its feet.

TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO TURN THE DISHWASHER UPSIDE-DOWN.

A

B

Fig. 5-01

Rev 0.0

13

Image 67

Contents INSTRUCTION MANUAL GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMSCONTENTS CONTENTSPage 1 INTRODUCTION INTRODUCTIONNomenclature of ﬁgures and tables This symbol highlights general information and warnings Tab Symbols used in this manual see tab2 DESCRIPTION AND USE OF THE CONTROLS 2.1 Upper panel USER INSTRUCTIONSUSER INSTRUCTIONS 2.2 Setting the washing program and switching on and offLISTED ETL SANITATIONBefore starting a washing program, make sure that 2.2.1 Switching on2.2.2 Selecting and starting the program 2.2.3 End of program2.2.4 Interrupting a program 2.2.6 Canceling the current program2.2.5 Changing the current program PROGRAM DELAY 2.2.7 Options3., 4., 5., 0., 1 2.2.8 Switching off2.3.1 Adjusting the water softener 2.3 Additional functionsWATER HARDNESS Water hardness table see tab3 ENERGY SAVING AND ENVIRONMENTAL RESPECT 4 REMOVING THE DISHES 5 TROUBLESHOOTING Alarms E1, E3, E4, immediately terminate the current program Contents Page Thank you for choosing one of our products. To use this dishwasher correctly and safely, please read this manual carefully. The manual is divided into sections giving you a step-by-step guide to all your appliance’s functions. The texts are easy to understand and are complete with detailed illustrations. Following the cleaning instruc- tions provided here will keep dishwasher performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasher This manual comprises the following sectionsINTRODUCTION WARNINGS 2 IMPORTANT SAFETY INSTRUCTIONSave this instructions WARNINGS ONLY USE RINSE-AID SPECIALLY FORMULATED FOR DOMESTIC DISHWASHERS DO NOT LEAN AGAINST OR STAND ON THE DISHWASHER RACKS DO NOT INTRODUCE ANIMALS INTO THE DISHWASHERATTEMPT TO REPAIR THE APPLIANCE THE MANUFACTURER DECLINES ALL RESPONSIBIL- ITY FOR DAMAGE TO PERSONS, ANIMALS OR PROPER- TY RESULTING FROM FAILURE TO OBSERVE THE ABOVE PRECAUTIONS, FROM TAMPERING WITH EVEN A SINGLE COMPONENT OF THE APPLIANCE, OR FROM THE USE OF UNORIGINAL SPARE PARTS 3 INSTALLATION AND HOOK-UP INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS adjust the water softening system add the regenerating salt 4 OPERATING INSTRUCTIONSadd the rinse-aid and detergent 4.1 Using the water softening system When using the dishwasher for the ﬁ rst time, in addition to the salt it is also necessary to add one liter of water to the container ED AS REQUIRED 4.2 Using the rinse-aid and detergent dispensers4.2.1 Adding the rinse-aid 4.2.2 Adjusting the rinse-aid dispenser setting4.2.3 Adding the detergent When a program with hot prewash is selected see program table in the “De- scription of Controls” manual, extra detergent must be placed in the cavity ref. A or B ﬁ g. 4-06, depending on models 4.3 General warnings and recommendations Items which are not dishwasher-safe MAKE SURE that the items being washed are dishwasher-safeDishes and objects in copper, tin, zinc or brass these tend to stain 4.4 Using the racks Con supporti fissi 4.4.1 Lower rackEsempi di caricamento Loading the lower rack see ﬁ gLoading examples 4.4.2 Cutlery basket see ﬁ g 4.4.3 Upper rack vedi ﬁ g. 4-12 EsempiLoading caricamentoexamples Loading the upper rack vedi ﬁ gAdjusting the upper rack 5.1 General warnings and recommendations 5 CLEANING AND USER-MAINTENANCENEVER USE ABRASIVE AND/OR CORROSIVE DETERGENTS TO CLEAN THE APPLIANCE 5.3 Cleaning the spray arms 5.2 Cleaning the water intake ﬁlter only some modelsRemoving the spray arms USER INSTRUCTIONS 5.4 Cleaning the ﬁlter unit 5.5 General warnings and recommendations for correct maintenance Before starting the dishwasher after prolonged disuse 5.6 Troubleshooting minor problemsIf the dishes do not come out clean, check that Prolonged disuseIf the dishes show signs of streaking, staining, etc., check that If the dishes fail to dry or remain dull, check thatIf there are visible traces of rust inside the tank 6 TECHNICAL DATA SEE TAB Contents CONTENTSPage 1 INTRODUCTION INTRODUCTIONNomenclature of ﬁgures and tables INTRODUCTION EDGE OF THE DOOR MUST NEVER BE REMOVED 2 SAFETY INFORMATIONREPAIR THE APPLIANCE TWO PEOPLE WEARING SAFETY GLOVES ARE REQUIRED TO LIFT THE DISHWASHERWARNINGS G I L 3 INSTALLATION MATERIALINSTALLATION INSTRUCTIONS B A D C Fmodels sta4645/sta8743 3.1 Kit supplied with dishwasher3.2 Kit supplied with dishwasher models pla8743 DIMENSIONS OF DISHWASHER See ﬁ g Only for free-standing models 5 INSTALLATION AND HOOK-UP5.1.1 Mounting the feet only for some models 5.1 Leveling5.1.2 Levelling the appliance FIRE HAZARD DO NOT COVER OR CRUSH THE CORD PLUG 5.2 Connections5.2.1 Connecting to the water supply 5.2.1.1 Connecting to the water tap Do not cut the inlet hose see ﬁ g min O4 cm 5.2.1.2 Connecting the drain hose Connecting to a drainMAX 100 cm 3-59/64”Available from any plumbing stockist Connecting to a “T” union of the drain circuitConnecting to a waste disposal unit with an air gap Connecting to the air gap no waste disposal unit A D C B Connecting to a waste disposal unit no air gapGrounding instructions 5.2.2 Electrical connections and warnings5.3 Commissioning 5.3.1 Installation procedure all modelsINSTALLATION INSTRUCTIONS Mount the door panel 5.3.2 Procedure for mounting the door panelsee ﬁ g Secure the door to the panel with the supplied screws. The panel must have a minimum thickness of 20 mm 25/32” see ﬁ g INSTALLATION INSTRUCTIONS models pla8743 5.3.3 Procedure for mounting the door panelINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5.3.4 Completion of installation all models Remove the adhesive band on the gasket see ﬁ g INSTALLATION INSTRUCTIONS 5.4 Testing 19 570 0074