Smeg ST115S User instructions, E7 E8 E9, Fault, Description, Turbine flow-regulatormalfunction

Page 34
E7

E7

E8

E9

User instructions

FAULT

DESCRIPTION

 

 

 

 

Turbine flow-regulator malfunction

 

(for the relevant models only)

 

 

The appliance is not able to "measure" the amount

 

of water loaded accurately. Interrupt the program

 

and switch off the dishwasher. Switch the

 

dishwasher back on, program it again and start

 

the washing cycle. If the problem persists, contact

 

the after-sales service.

 

 

 

 

Alternate washing system malfunction

 

Interrupt the program and switch off the dishwasher.

 

Switch the dishwasher back on, program it again and

 

start the washing cycle. If the problem persists,

 

contact the after-sales service.

 

 

 

 

Water intake system malfunction

 

Contact the after-sales service.

 

Light off

Light on

Light flashing

If an alarm occurs the appliance interrupts the program in progress and signals a fault.

Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately.

The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program.

The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed.

To “reset” an alarm is necessary:

Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again.

If the malfunction persists, contact your authorised Service Centre.

33

Image 34
Contents Page Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCE2. Installation and hook-up Installation instructions2.1 Water supply connection CONNECTING TO THE WATER SUPPLY DRAIN CONNECTION2.2 Electrical connection and precautions L = brown N = blue = yellow-greenFuse replacement FOR GREAT BRITAIN ONLYSELECTED PROGRAM INDICATOR LIGHTS User instructions3. Description of the controls 3.1 Upper panelDELAYED START BUTTON SETTING THE WASHING PROGRAM AND SWITCHING ONDELAYED START LIGHTS User instructions SELECTING HALF LOAD WASH 3.2 Washing programsBefore starting a washing program make sure that available in all programs except the soak programCHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT END OF CYCLE REMOVING THE DISHES4. Operating instructions 4.1Using the water softening systemADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-freebut contain natural enzymes 4.3 General warnings and recommendations Items which are not dishwasher-safe LOWER BASKET 4.4 Using the basketsLOADING THE LOWER BASKET insert CUTLERY BASKETUPPER BASKET closedLOADING THE UPPER BASKET Loading examples Models with cutlery racksADJUSTING THE UPPER BASKET Version BUser instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1General warnings and recommendations•Fill the rinse aid dispenser CLEANING THE FILTER UNITPROLONGED DISUSE Shut off the water supply tapTROUBLESHOOTING MINOR PROBLEMS If the program fails to start, check thatthere is rinse aid inside the special container Safety level 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6Alternate washing system malfunction E7 E8 E9Turbine flow-regulatormalfunction Water intake system malfunctionWidth TECHNICAL DATAWater supply pressure Electrical characteristics Height depending on models Capacity