Smeg ST115S Installation instructions, Installation and hook-up, Water supply connection

Page 6
Installation instructions

Installation instructions

2. Installation and hook-up

Remove the polystyrene basket retainers.

Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. Make sure to tighten the locking ring-nut once the pipes have been placed in the direction required. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass.

Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.

Building-in a dishwasher underneath a ceramic hob is absolutely forbidden.

A dishwasher can be built-in underneath a conventional hob provided there is no break in the kitchen worktop, and the dishwasher and hob are installed and secured correctly, so that no hazards are generated.

When installing the dishwasher in a compartment next to one or more other appliances, it is essential to comply with all the recommendations provided by the appliance’s manufacturer (minimum distances, installation procedures, etc.).

Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.

2.1 Water supply connection

Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.

The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Page Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCEInstallation instructions 2. Installation and hook-up2.1 Water supply connection CONNECTING TO THE WATER SUPPLY DRAIN CONNECTION2.2 Electrical connection and precautions L = brown N = blue = yellow-greenFuse replacement FOR GREAT BRITAIN ONLYSELECTED PROGRAM INDICATOR LIGHTS User instructions3. Description of the controls 3.1 Upper panelSETTING THE WASHING PROGRAM AND SWITCHING ON DELAYED START BUTTONDELAYED START LIGHTS User instructions SELECTING HALF LOAD WASH 3.2 Washing programsBefore starting a washing program make sure that available in all programs except the soak programCANCELLING THE CURRENT PROGRAM CHANGING THE PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT END OF CYCLE REMOVING THE DISHES4. Operating instructions 4.1Using the water softening systemADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-freebut contain natural enzymes 4.3 General warnings and recommendations Items which are not dishwasher-safe 4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET insert CUTLERY BASKETUPPER BASKET closedLOADING THE UPPER BASKET Loading examples Models with cutlery racksADJUSTING THE UPPER BASKET Version BUser instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1General warnings and recommendations•Fill the rinse aid dispenser CLEANING THE FILTER UNITPROLONGED DISUSE Shut off the water supply tapTROUBLESHOOTING MINOR PROBLEMS If the program fails to start, check thatthere is rinse aid inside the special container Safety level 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6Alternate washing system malfunction E7 E8 E9Turbine flow-regulatormalfunction Water intake system malfunctionWidth TECHNICAL DATAWater supply pressure Electrical characteristics Height depending on models Capacity
Top Page Image Contents