Smeg ST115S User instructions, Adding The Rinse Aid, Adjusting The Rinse Aid Dispenser Setting

Page 19
ADDING THE RINSE AID

User instructions

ADDING THE RINSE AID

The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door.

To add rinse aid:

Open the door.

Rotate the container cap anticlockwise by ¼ of a turn and remove it.

Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates.

Replace the cover and turn it in a clockwise direction.

Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam.

ADJUSTING THE RINSE AID DISPENSER SETTING

The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser’s selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position.

To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it.

Then use a screwdriver to rotate the rinse aid selector to the desired position.

Replace the cap, turning it clockwise.

The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains.

If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting.

18

Image 19
Contents Page Contents NEVER BE REMOVED Safety instructions1. Safety and operating instructions USES OTHER THAN THOSE DESCRIBED ABOVETHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELS2. Installation and hook-up Installation instructions2.1 Water supply connection DRAIN CONNECTION CONNECTING TO THE WATER SUPPLYL = brown N = blue = yellow-green 2.2 Electrical connection and precautionsFOR GREAT BRITAIN ONLY Fuse replacement3.1 Upper panel User instructions3. Description of the controls SELECTED PROGRAM INDICATOR LIGHTSDELAYED START BUTTON SETTING THE WASHING PROGRAM AND SWITCHING ONDELAYED START LIGHTS User instructions available in all programs except the soak program 3.2 Washing programsBefore starting a washing program make sure that SELECTING HALF LOAD WASHCHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT REMOVING THE DISHES END OF CYCLE4.1Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGADDING THE DETERGENT The market offers liquid and powder detergents with differing chemical compositions, which may contain phosphates, or be phosphate-freebut contain natural enzymes 4.3 General warnings and recommendations Items which are not dishwasher-safe LOWER BASKET 4.4 Using the basketsLOADING THE LOWER BASKET closed CUTLERY BASKETUPPER BASKET insertLoading examples Models with cutlery racks LOADING THE UPPER BASKETVersion B ADJUSTING THE UPPER BASKETUser instructions 5.1General warnings and recommendations 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER CLEANING THE SPRAY ARMSShut off the water supply tap CLEANING THE FILTER UNITPROLONGED DISUSE •Fill the rinse aid dispenserIf the program fails to start, check that TROUBLESHOOTING MINOR PROBLEMSthere is rinse aid inside the special container E1 E2 E3 E4 E5 E6 6. TroubleshootingFAULT Safety levelWater intake system malfunction E7 E8 E9Turbine flow-regulatormalfunction Alternate washing system malfunctionHeight depending on models Capacity TECHNICAL DATAWater supply pressure Electrical characteristics Width