Smeg STA643PQ manual Installation instructions, Installation and hook-up, Water supply connection

Page 6

Installation instructions

Installation instructions

2. Installation and hook-up

Remove the polystyrene basket retainers.

Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw them to the adjacent units. To facilitate the installation procedure, the intake and drain hoses can be positioned in any direction; make sure that the hoses are not kinked, crushed or pulled too tightly. Make sure to tighten the locking ring-nut once the pipes have been placed in the direction required. A hole at least 8 cm in diameter is required to allow the power supply cable and pipes to pass.

Level the appliance on the floor using its adjustable feet. This operation is essential for ensuring correct operation of the dishwasher.

Building-in a dishwasher underneath a ceramic hob is absolutely forbidden.

A dishwasher can be built-in underneath a conventional hob provided there is no break in the kitchen worktop, and the dishwasher and hob are installed and secured correctly, so that no hazards are generated.

When installing the dishwasher in a compartment next to one or more other appliances, it is essential to comply with all the recommendations provided by the appliance’s manufacturer (minimum distances, installation procedures, etc.).

Some models are equipped with only one adjustable foot at the rear, which can be adjusted by turning the screw on the lower front part of the appliance.

2.1 Water supply connection

Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance.

The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused.

5

Image 6

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS AQUASTOP MODELS APPLIANCEInstallation instructions 2. Installation and hook-up2.1 Water supply connection CONNECTING TO THE WATER SUPPLY DRAIN CONNECTION2.2 Electrical connection and precautions NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD Fuse replacement FOR GREAT BRITAIN ONLYSELECTED PROGRAM INDICATOR LIGHTS User instructions3. Description of the controls 3.1 Upper panel“3/1” OPTION LIGHT 13 INFORMATION DISPLAY SETTING THE WASHING PROGRAM AND SWITCHING ON“3/1” OPTION BUTTON HALF LOAD BUTTONThe RAPID CYCLE 6, “3/1” 8, HALF LOAD WASH 10 and DELAYED START DURATION POWERVery dirty pans MINUTESThe correct amount of detergent has been added to the dispenser 3.2 Washing programsBefore starting a washing program make sure that RAPID CYCLES available in all programs except the soak programSELECTING HALF LOAD WASH available in all programs except the soak programDELAYED START available in all programs except the soak program TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT CANCELLING THE CURRENT PROGRAMCHANGING THE PROGRAM TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTEND OF CYCLE REMOVING THE DISHES4. Operating instructions 4.1 Using the water softening systemADJUSTING THE WATER SOFTENING SYSTEM 4.2 Using the rinse aid and detergent dispensers WATER HARDNESS TABLEADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDADDING THE DETERGENT During the washing cycle, the dispenser will be opened automaticallyUser instructions 4.3 General warnings and recommendations Correct loading of the dishes helps ensure optimal washing resultsMAKE SURE that the items being washed are dishwasher-safe Items which are not dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stain4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET UPPER BASKET LOADING THE UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories ADJUSTING THE UPPER BASKET Version BUser instructions CLEANING THE SPRAY ARMS 5. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 5.1 General warnings and recommendationsPROLONGED DISUSE CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE Fill the rinse aid dispenser Shut off the water supply tapBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that Reconnect the water intake hose and open the tap againIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank Safety level 6. TroubleshootingFAULT E1 E2 E3 E4 E5 E6Alternate washing system malfunction E7 E8 E9Turbine flow-regulator malfunction Water intake system malfunctionWidth TECHNICAL DATAElectrical characteristics Height depending on models Capacity Water supply pressure