Smeg STA643PQ manual Installation instructions, For Great Britain Only, Fuse replacement

Page 9

Installation instructions

FOR GREAT BRITAIN ONLY:

THIS APPLIANCE MUST BE EARTHED.

Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

1.Remove the fuse cover A and fuse B.

2.Fit replacement 13A fuse into fuse cover.

3.Refit both into plug.

The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.

Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local electrical store.

Image 9

Contents GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Safety and operating instructions Safety instructionsUSES OTHER THAN THOSE DESCRIBED ABOVE NEVER BE REMOVEDTHIS DISHWASHER MUST BE USED BY ADULTS APPLIANCE AQUASTOP MODELSInstallation instructions 2. Installation and hook-up2.1 Water supply connection DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY2.2 Electrical connection and precautions NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD FOR GREAT BRITAIN ONLY Fuse replacement3. Description of the controls User instructionsSELECTED PROGRAM INDICATOR LIGHTS 3.1 Upper panel“3/1” OPTION BUTTON 13 INFORMATION DISPLAY SETTING THE WASHING PROGRAM AND SWITCHING ON“3/1” OPTION LIGHT HALF LOAD BUTTONThe RAPID CYCLE 6, “3/1” 8, HALF LOAD WASH 10 and DELAYED START Very dirty pans POWERDURATION MINUTESBefore starting a washing program make sure that 3.2 Washing programsThe correct amount of detergent has been added to the dispenser RAPID CYCLES available in all programs except the soak programSELECTING HALF LOAD WASH available in all programs except the soak programDELAYED START available in all programs except the soak program CHANGING THE PROGRAM CANCELLING THE CURRENT PROGRAMTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTREMOVING THE DISHES END OF CYCLE4.1 Using the water softening system 4. Operating instructionsADJUSTING THE WATER SOFTENING SYSTEM WATER HARDNESS TABLE 4.2 Using the rinse aid and detergent dispensersADDING THE RINSE AID ADJUSTING THE RINSE AID DISPENSER SETTINGDuring the washing cycle, the dispenser will be opened automatically ADDING THE DETERGENTUser instructions 4.3 General warnings and recommendations Correct loading of the dishes helps ensure optimal washing resultsMAKE SURE that the items being washed are dishwasher-safe Dishes and objects in copper, tin, zinc or brass these tend to stain Items which are not dishwasher-safe4.4 Using the baskets LOWER BASKETLOADING THE LOWER BASKET CUTLERY BASKET LOADING THE UPPER BASKET UPPER BASKETDepending on the models, the basket may be equipped with some or all of the following accessories Version B ADJUSTING THE UPPER BASKETUser instructions CLEANING THE WATER INTAKE FILTER 5. Cleaning and maintenanceCLEANING THE SPRAY ARMS 5.1 General warnings and recommendationsGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE CLEANING THE FILTER UNITPROLONGED DISUSE Fill the rinse aid dispenser Shut off the water supply tapIf the dishes are not being cleaned properly, check that TROUBLESHOOTING MINOR PROBLEMSBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE Reconnect the water intake hose and open the tap againIf the dishes fail to dry or remain dull, check that If the dishes show signs of streaking, staining, etc., check thatIf there are visible traces of rust inside the tank FAULT 6. TroubleshootingSafety level E1 E2 E3 E4 E5 E6Turbine flow-regulator malfunction E7 E8 E9Alternate washing system malfunction Water intake system malfunctionElectrical characteristics TECHNICAL DATAWidth Height depending on models Capacity Water supply pressure