Smeg CE6IPX manual Using the Main Oven, First use, Setting the current time, Selecting a function

Page 10

Instructions for the User

10. USING THE MAIN OVEN

10.1 First use

At first use, or after a power failure, the oven's display will show a flashing symbol. To be able to start any cooking function with the main oven, the current time must be set.

10.2 Setting the current time

To adjust the current time with the flashing display:

Press the buttons or to decrease or increase the time shown. If the button is held down in one direction the time changes faster.

When any button is released, after a few seconds the display will stop flashing and only the colon seperating the hour and minutes will flash to indicate its correct operation (The symbol will be

shown on the display).

It might become necessary to change the current time, for example for daylight savings time.

hold down the button for a few seconds until the symbol stops flashing. Repeat the operations described in point “10.2 Setting the current time”.

10.2.1Using the minute minder

The minute minder can be used during cooking or when the oven is turned off. The setting procedure is the same for both cases.

Press the button briefly, the symbol will flash and the display will show the symbol (or the time remaining from a previously programmed count).

Press the buttons or to increase or decrease the minute minder time from 00:01 to 03:59 (hold the button down to go faster). After a few seconds the count will begin and the remaining time and the

non-flashing symbol will appear on the display.

To reset the minute minder, press the and buttons at the same time for approximately one second.

Warning: The minute minder does not stop the cooking but rather informs the user when the set time has run out. To turn off the oven, turn the PT2 knob to the O position.

Modifying the programmed data:

Once the count has begun, the previously set data can be modified. Repeat the operations described in point “10.2.1 Using the minute minder”.

10.3 Selecting a function

A cooking function can be selected by simply turning PT2 to the right or left to the desired function. After having selected the cooking function, use the PT1 knob to select the desired temperature.

Cooking is preceded by a preheating stage, which allows the oven to heat to the cooking temperature more quickly. The symbol flashes on the display to indicate that this stage is in progress. When the

preheating stage is over, the symbol will remain on and a buzzer will sound to indicate that the food can be placed inside the oven.

41

Image 10
Contents Index Precautions for USE Plate Must not be RemovedRecycling Instructions OUR Environment Policy Intended USE Safety PrecautionsNever Attempt to Repair the Appliance Yourself Getting to Know Your Ovenl General DescriptionAvailable Accessories Before InstallationAccessories available on request Using the Rotisserie ROD when present Description of the Controls on the Front Panel Main Oven Functions Selection Knob PT2 Main Oven Temperature Selection Knob PT1HOB Control Knob First use Using the Main OvenSetting the current time Selecting a functionModifying the data set Programmed cooking procedures10.4.1Semiautomatic cooking 10.4.2Automatic cookingModifying the data set during cooking Cooking with selection of a recipeAutomatic cooking with selection of a recipe Making permanent changes to a recipe Table of predefined recipes Secondary menu Cooking in the Oven Description of the selected functionsHints on Using the Accessories Cooking Hints and TipsCooking tables Using the HOB Cooking zones180 mm Zone number Zone Diameter Power consumed 145 mmTotal power consumed 210 mmResidual heat Cookware detector signalOperation Activating temperature Cooking hob lock-outThermal protection glass-ceramic hob Keep Warm FunctionCleaning and Maintenance Pyrolysis automatic oven cleaning on some models only Before starting the automatic cleaning cycleSetting the cleaning cycle Removing the door Extraordinary MaintenanceChanging the light bulb Removing the door sealOven does not heat up What to do ifOven display is completely off Controls do not respondInstalling the Appliance Electrical connectionPositioning and levelling the appliance depending on model