Sub-Zero Freezer Level T H E U N I T, Turn power back on to the wall outlet

Page 11

BUILT-INI N S TA L L AT I O N I N S T R U C T I O N S

WATER LINE C O N N E C T I O N

To connect the ice maker water line, remove the 1/4" compression fitting from its plastic bag and join the water supply line to the solenoid valve. Refer to illustration 7 below. NOTE:

The water valve can be removed from the mounting bracket to gain easier access to water connection. Be sure to purge the line before making the final connection.

IMPORTANT NOTE: Turn on the water supply and check all fittings for leaks. Make certain the electrical harness is attached to the solenoid.

In areas with water of high mineral content, the use of an in-line water filter is recom- mended. Make sure the filter is positioned and accessible for replacement when necessary.

IMPORTANT NOTE: Let your customer know that the ice maker will not fill with water immediately, and that the first few batches of ice produced should be discarded. Allow 24 hours for proper ice production.

LEVEL T H E U N I T

Once the unit is in position, extend the front leveling legs down by turning the legs counter- clockwise and adjust the height. The rear height adjustment can be made from the front of the base. Turn the 5/16" hex bolt clockwise to raise the unit or counterclockwise to lower it. Refer to illustration 8 below. When the unit is leveled properly, or squared off, door adjustments are less likely to be necessary.

IMPORTANT NOTE: Be sure to reference leveling of the unit to the floor and not to surrounding cabinetry. This could affect the operation of the unit, such as door(s) not closing properly.

For proper alignment, place the level on the top and side of the unit's main frame for leveling reference points.

After the unit has been leveled, make sure the drain pan is installed properly and install the kickplate. Refer to illustration 9 below.

IMPORTANT NOTE: The kickplate must be removed for servicing. The floor cannot inter- fere with removal. Refer to label mounted on kickplate support for height clearance.

Replace the grille by reversing the procedure outlined on page 9. If you’re using a panel grille, see Overlay Grille Panels on page 17.

Turn power back on to the wall outlet.

ELECTRICAL

CONNECTION

SOLENOID

VALVE

Illus. 7

REAR

ADJUSTMENT

FRONT

LEVELERS

Illus. 8

Illus. 9

Dimensions in parentheses are in

 

millimeters unless otherwise specified.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Installation Instructions N T E N T S To O L S a N D M AT E R I a L S R E Q U I R E D T E P R E P a R AT I O N S TA L L AT I O N S P E C I F I C AT I O N S BUILT-INI N S TA L L AT I O N S P E C I F I C AT I O N SE R a L L D I M E N S I O N S L R E F R I G E R ATO R a L L F R E E Z E RModel D E RModel Model 611G Model 650G D E B Y- S I D E Dimensions in parentheses are Models 601R, 601RG and 601F-framed Grille R E M O V a LANTI-TIPB L O C K I N G K I T Position T H E U N I T BUILT-INI N S TA L L AT I O N I N S T R U C T I O N SLevel T H E U N I T Turn power back on to the wall outletFramed P a N E L S A M E D N E L SFramed Panel I N S TA L L AT I O N PA N E L S I G N I S E D PA N E L SPA RT I a L F R a M E D a C C E S S O RY K I T A M E D R E T RO F I T a C C E S S O RY K I TModel 601R Framed Panel S P E C I F I C AT I O N SA M E D D O O R PA N E L S A M E D PA N E L SA M E D N E L S PA RT I a L F R a M E D D O O R PA N E L SN E L G R I L L E O P T I O N Overlay Panel I N S TA L L AT I O N Overlay P a N E L S E R L AY N E L SOverlay Grille PA N E L S Overlay Panel I N S TA L L AT I O NE R L AY PA N E L S Overlay Panel S P E C I F I C AT I O N SE R L AY D O O R PA N E L S E R L AY G R I L L E P a N E L S 24 1/ 4 D E PA N E L I N S TA L L AT I O N O P T I O N SHinge a D J U S T M E N T Completing T H E I N S TA L L AT I O N Anchor T H E U N I TO U N I T S a N C H O R E D to G E T H E R I T a N C H O R E D to C a B I N E T RYCompleting T H E I N S TA L L AT I O N E G R E E Door Stop Installation C H E C K L I S TN TA C T F O R M AT I O N Service I N F O R M AT I O NMail Address customerservice@ subzero.com S TA L L AT I O N C H E C K L I S T0 0
Top Page Image Contents