Sub-Zero Freezer Completing T H E I N S TA L L AT I O N Anchor T H E U N I T

Page 21

COMPLETING T H E I N S TA L L AT I O N

ANCHOR T H E U N I T

After door and side panels have been installed, the unit has been leveled and door adjustment completed, anchor the unit to the opening.

This will assure a proper fit and a secure installation. The Sub-Zero Anchoring Kit (part #4200900), available from your Sub-Zero dealer, includes the necessary hardware.

IMPORTANT NOTE: Be sure to level and square the unit before anchoring it.

T W O U N I T S A N C H O R E D TO G E T H E R

Drill three 13/64" holes through the middle trim of both units.

Using the Loctite on the screws, install the three Chicago screw posts.

Recheck the units for level.

Drill three 3/16" holes through both outer trims. Refer to illustration 18 below.

Using a 1/8" drill bit, drill into the cabinetry for a pilot hole.

Install all six Sems to the cabinetry.

Do not drill through the model and serial number plate.

U N I T A N C H O R E D TO C A B I N E T RY

First, make sure units have been leveled and aligned, and doors adjusted.

Drill three 3/16" holes through both outer trims. Refer to illustration 19 below.

Drill a 1/8" pilot hole into the cabinetry.

Install all six Sems.

HINGE A D J U S T M E N T

Check to make sure the doors are properly aligned. If not, the door hinges will have to be adjusted. Remove the two small shipping screws from the top and bottom hinge as shown in illustrations 20 and 21 below. Next, using a 1/8" allen head wrench, loosen the allen head screws in the top and bottom hinge. Loosen the allen head screws only slightly, so that the door will remain in position as you adjust it. You will now be able to move the door to the left, right, or in and out. Once the adjustments are made, tighten the allen head screws—do not put the shipping screws back.

171/8"(435)

171/8"(435)

171/8"(435)

171/8"

(435)

171/8"(435)

171/8"(435)

171/8"(435)

171/8"

(435)

Illus. 20

Illus. 21

Illus. 18

Illus. 19

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Installation Instructions N T E N T S To O L S a N D M AT E R I a L S R E Q U I R E D T E P R E P a R AT I O N E R a L L D I M E N S I O N S BUILT-INI N S TA L L AT I O N S P E C I F I C AT I O N SL R E F R I G E R ATO R a L L F R E E Z E R S TA L L AT I O N S P E C I F I C AT I O N SD E R Model Model 611G Model 650GModel D E B Y- S I D E Dimensions in parentheses are Models 601R, 601RG and 601F-framed Grille R E M O V a LANTI-TIPB L O C K I N G K I T Position T H E U N I T BUILT-INI N S TA L L AT I O N I N S T R U C T I O N SLevel T H E U N I T Turn power back on to the wall outletA M E D N E L S Framed Panel I N S TA L L AT I O NFramed P a N E L S PA RT I a L F R a M E D a C C E S S O RY K I T I S E D PA N E L SA M E D R E T RO F I T a C C E S S O RY K I T PA N E L S I G NA M E D D O O R PA N E L S Framed Panel S P E C I F I C AT I O N SA M E D PA N E L S Model 601RPA RT I a L F R a M E D D O O R PA N E L S N E L G R I L L E O P T I O NA M E D N E L S Overlay Panel I N S TA L L AT I O N Overlay P a N E L S E R L AY N E L SOverlay Grille PA N E L S Overlay Panel I N S TA L L AT I O NOverlay Panel S P E C I F I C AT I O N S E R L AY D O O R PA N E L SE R L AY PA N E L S E R L AY G R I L L E P a N E L S 24 1/ 4 D E PA N E L I N S TA L L AT I O N O P T I O N SO U N I T S a N C H O R E D to G E T H E R Completing T H E I N S TA L L AT I O N Anchor T H E U N I TI T a N C H O R E D to C a B I N E T RY Hinge a D J U S T M E N TCompleting T H E I N S TA L L AT I O N E G R E E Door Stop Installation C H E C K L I S TMail Address customerservice@ subzero.com Service I N F O R M AT I O NS TA L L AT I O N C H E C K L I S T N TA C T F O R M AT I O N0 0
Top Page Image Contents