Sub-Zero Freezer Grille R E M O V a L, Models 601R, 601RG and 601F-framed

Page 9

BUILT-INI N S TA L L AT I O N I N S T R U C T I O N S

UNPACK T H E U N I T

Uncrate the unit, remove its wood base and discard the shipping bolts that hold the wood base to the bottom of the unit. Remove all packing materials and tape.

IMPORTANT NOTE: Do not discard the kickplate, anti-tip blocking kit and hardware. These items will be needed for installation.

Retract the front leveling legs to allow you to move the unit more easily during installation. You will extend the leveling legs when the unit is in its final position to reduce the possibility of the unit tipping forward.

Remove the drain pan from the base of the unit to avoid damage to the drain pan, and allow for proper placement of the appliance dolly.

Keep door(s) and drawer taped closed while moving unit.

GRILLE R E M O V A L

In order to prevent damage to the grille and to access the power cord, the top grille assembly should be removed prior to moving the unit.

Models 611, 611G, 650, 650G, 661, 642, 685,

632 and 695—framed and stainless steel:

Remove three counter-sunk grille screws at the bottom of the grille and cut the red nylon shipping strap. NOTE: Grille screws are accessed with door(s) open. Then tilt the grille forward and release the springs from behind the grille. Refer to illustration 1 below.

Models 601R, 601RG and 601F—framed and

overlay: Remove the two black screws in the lowest louver of the grille. Tilt the bottom of the grille out and away. It will release from the top of the grille. Refer to illustration 2 below.

Models 601R, 601RG and 601F—stainless

steel: The lower grille snaps out by pulling forward on the bottom of the grille.

Models 611, 611G, 650, 650G, 661, 642, 685,

632 and 695—overlay:First, remove the inner grille panel assembly as shown in illustration 3 below. Lift up, then pull out at the bottom, pull the top section down and out of the top key slot. Remove the five mounting screws that hold the outer grille panel assembly to the top compartment. Refer to illustration 4.

Grille Springs

Grille

Screws

(inside door)

Illus. 1

Illus. 2

Illus. 3

Illus. 4

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Instructions N T E N T S To O L S a N D M AT E R I a L S R E Q U I R E D T E P R E P a R AT I O N E R a L L D I M E N S I O N S BUILT-INI N S TA L L AT I O N S P E C I F I C AT I O N SL R E F R I G E R ATO R a L L F R E E Z E R S TA L L AT I O N S P E C I F I C AT I O N SD E R Model Model 611G Model 650GModel D E B Y- S I D E Dimensions in parentheses are Models 601R, 601RG and 601F-framed Grille R E M O V a LANTI-TIPB L O C K I N G K I T Position T H E U N I T BUILT-INI N S TA L L AT I O N I N S T R U C T I O N SLevel T H E U N I T Turn power back on to the wall outletA M E D N E L S Framed Panel I N S TA L L AT I O NFramed P a N E L S PA RT I a L F R a M E D a C C E S S O RY K I T I S E D PA N E L SA M E D R E T RO F I T a C C E S S O RY K I T PA N E L S I G NA M E D D O O R PA N E L S Framed Panel S P E C I F I C AT I O N SA M E D PA N E L S Model 601RPA RT I a L F R a M E D D O O R PA N E L S N E L G R I L L E O P T I O NA M E D N E L S Overlay Panel I N S TA L L AT I O N Overlay P a N E L S E R L AY N E L SOverlay Grille PA N E L S Overlay Panel I N S TA L L AT I O NOverlay Panel S P E C I F I C AT I O N S E R L AY D O O R PA N E L SE R L AY PA N E L S E R L AY G R I L L E P a N E L S 24 1/ 4 D E PA N E L I N S TA L L AT I O N O P T I O N SO U N I T S a N C H O R E D to G E T H E R Completing T H E I N S TA L L AT I O N Anchor T H E U N I TI T a N C H O R E D to C a B I N E T RY Hinge a D J U S T M E N TCompleting T H E I N S TA L L AT I O N E G R E E Door Stop Installation C H E C K L I S TMail Address customerservice@ subzero.com Service I N F O R M AT I O NS TA L L AT I O N C H E C K L I S T N TA C T F O R M AT I O N0 0
Top Page Image Contents