Agilent Technologies 89441A manual To connect the optional keyboard

Page 67

Preparing the Analyzer for Use

To connect the optional keyboard

The analyzer may be connected to an optional external keyboard. The keyboard remains active even when the analyzer is not in alpha entry mode. This means that you can operate the analyzer using the external keyboard rather than the front panel. Pressing the appropriate keyboard key does the same thing as pressing a hardkey or a softkey on the analyzer’s front panel.

1Set the IF section’s power switch to on ( l ).

2Connect the round plug on the keyboard cable to the KEYBOARD connector on the analyzer’s front panel. Make sure to align the plug with the connector pins.

	3 Connect the other end of the keyboard cable to the keyboard.
		In addition to the U.S. English keyboard, the analyzer supports U.K. English,
Caution
		German, French, Italian, Spanish, and Swedish. Use only the Hewlett-Packard
		approved keyboard for this product. Hewlett-Packard does not warrant damage
		or performance loss caused by a non-approved keyboard. See the beginning of
		this guide for part numbers of approved Hewlett-Packard keyboards.

7-17

Image 67

Contents Agilent Technologies 89441A Getting Started Guide Analyzer at a Glance Front Panel IiiThis page left intentionally blank Saftey Summary Fuses Safety Symbols Notation Conventions This Book This page left intentionally blank Table of Contents Xii General TasksUsing Online Help Enter the online help system Press Help To learn about online helpTo display help for hardkeys and softkeys To display a related help topic To select a topic from the help index Page Making Simple Noise Measurements Start an averaged measurement To measure random noiseTurn on the band power markers To measure band powerTurn on the carrier-to-noise marker To measure signal to noise ratiosCarrier-to-noise ratio normalized to one Hertz Page Using Gating to Characterize a Burst Signal Display should now appear as shown below To Use Time GatingSet up the time gating and examine the first burst Configure the display and the measurementExamine the second burst Page Measuring Relative Phase To measure the relative phase of an AM signal Measuring Relative Phase Zero the offset marker on the carrier To measure the relative phase of an PM signalCharacterizing a Filter Have option AY7 To set up a frequency response measurementIf section for network measurements Press Auto Scale To use the absolute marker To use the relative marker To use the search marker Specify phase data for the second trace To display phaseActivate the second trace and select a coherence measurement To display coherenceGeneral Tasks To set up peripherals General Tasks To save data with an internal or RAM disk Press Return To recall data with an internal or RAM diskTo format a disk Define a constant To create a math functionDefine a math function Press Math, define F1 To use a math function Press measurement state or input/source state To display a summary of instrument parametersPage Preparing the Analyzer for Use Preparing the Analyzer for Use To chassis ground Analyzer cabinet can subject the operator to lethal voltages To do the incoming inspection Power if it is damagedPreparing the Analyzer for Use To connect the sections Preparing the Analyzer for Use To install the analyzer Select To change the if section’s line-voltage switchTo change the RF section’s line-voltage switch To change the if section’s fuse RF Section To change the RF section’s fuse Internet protocol address Return To connect the analyzer to a LANTo connect the analyzer to a parallel device To connect the analyzer to a serial deviceTo connect the analyzer to an external monitor To connect the analyzer to an Gpib deviceTo connect the optional keyboard Set the if section’s power switch to on lConnect the other end of the keyboard cable to the keyboard To connect the optional minimum loss pad To store the analyzer To clean the screenElectricity which can damage electronic components To transport the analyzerIf the if section will not power up If the RF section will not power up If the analyzer’s stop frequency is 10 MHz Page Index Basic HT Gpib SNR HT Dqpsk HTQAM SNRSee also traces Gpib HT FSKGpib LAN Manuals, for this product HT See LAN RAM QAM HTSee knob RPGSource LED Tdma Sync not Found HTEXT Trigger LED HT PSD HTVSB Page Agilent 89400-Series Documentation Roadmap Need Assistance?