Creda E430E Know Your Timer, Clockface, Symbols, Timer Function Buttons, Auto Cooking Programme

Page 10

Know Your Timer

CLOCKFACE

The timer incorporates a 24 hour clock.

Ensure the correct time of day is always set, before using you cooker.

PLEASE NOTE THAT THE DISPLAY WILL DIM BETWEEN 22.00

HOURS AND 06.00 HOURS TO PREVENT GLARE.

However, should you operate the timer during these hours the display will return to normal brightness for a few seconds and then dim again.

SYMBOLS

will light up when you select a Minute Minder Period and will remain lit for the period set. At the end of the Minute Minder Period, the timer will emit an audible tone for 2 minutes, the symbol will start to flash and will continue to flash until the Minute Minder function is cancelled.

This “Cookpot” symbol will light up either:–

–When you press the Cook Period Button and set a length of time for an Auto Cooking Programme. (It will go out again a few seconds after you release the timer buttons).

–During the actual Cook Period.

“AUTO” will light up:–

–When the timer is first turned on it will flash. (It will go out when a time of day is set.

–When an Auto Cooking Programme has been set.

The “Auto” symbol will flash at the end of an Auto Cooking programme to indicate that the programme has finished.

(When the “Auto” symbol is flashing, to return the oven to Manual operation, turn the oven controls off, ensure that the correct time of day is set, and press the “Manual” button twice – The “Auto” symbol will go out).

Note: If at any time the display shows a ‘KEY’ symbol, it is likely that the timer has been set incorrectly. OVEN COOKING IS NOT POSSIBLE. The ‘KEY’ symbol can be deleted and the cooker returned to manual operation by:

-Simultaneously pressing the Minute Minder and the Cook Period buttons for a period of approximately 8 seconds.

-Releasing the buttons and pressing the ‘+’ button.

TIMER FUNCTION BUTTONS

Minute Minder Here you can set a time period of up to 23 hours 59 minutes, that will count down.

ButtonWhen it reaches zero, the timer will emit an audible tone.

For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.

AUTO COOKING PROGRAMME

Cook Period Button Cook Period is the actual length of time for which, the timer will switch the oven(s) on as part of an “Auto Cooking” programme.

(e.g. If you set 2 hours, the food will be cooked for 2 hours).

End Time Button The time of day at which you want an “Auto Cooking” programme to end.

For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.

Notes:

-When setting an Auto Cooking programme you will need to set the oven controls(s) to the required temperature(s) when you set the timer.

-If an Auto Cooking programme has been set the oven(s) will only operate during the pre-programmed time.

Manual Button Needs to be pressed to cancel an Auto Cooking programme and return the ovens(s) to Manual operation.

“+” and “–” Buttons Used to adjust the various timer function settings.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents N230E / E430E / R430E Installation & User Instructions Creda Answer Centre 08701 54 64 Creda Answer Centre 08701 54 64Contents Disposal of your product Introduction89/336/EEC 73/23/EEC 92/31/EEC 93/68/EEC Safety Advice Safety InformationAlways Safety Information Never Features Grill Setting Control ControlsOven Timer Operation Timer Function Buttons Know Your TimerSymbols ClockfaceSetting the Time of DAY Setting the Minute MinderAuto Cooking Programmes Electronic Clock and Automatic Oven Timer Operation Other Notes on Timer Operation Top Oven Shelf Positioning for Grilling Grill Pan and HandleGrill Pan Food Grid and Anti-Splash Tray StepUsing the Top Oven for Solarplus Grilling For Half Grill Left hand side only Operation when using the Top Oven for GrillingGrillFull = Full Grill Function = Maximum Grill Setting Grill Controls ExampleSetting FoodConventional Grilling N230E Grill pan handleEasy Glide Shelf Using the Top Oven as a Convection OvenShelf Positioning Plate Warming Operation when using the Top Oven as a Convection OvenNever use the grill setting control a when warming plates Top Oven UtensilsUsing the Main Oven for Fan Cooking Main Oven Shelf Positioning for Fan OvenLight only Setting Using the Main Oven for Other FunctionsFan Only Setting Operation To assist in defrostingAdvantages of Slow cooking are Slow SettingPoints to consider when preparing food for Slow cooking OperationTemperature Conversion Chart Conventional Convection Fan Mark OvenOven Temperature Charts Meat Top Oven Convection CookingOven Temperature Charts Baking Baking General Cooking Results Not SatisfactoryGrill TOP Oven BakingHow Credaclean works Care and CleaningCredaclean Oven Liners E430E / N230E CleaningRemovable Grill Roof Panel not all models Cleaning GRILL, TOP Oven and Main OvenGrill Pan, Meat Pans & Oven Shelves Solarplus GrillHOW to Clean the Lamp Lens Replacement of the Oven LampOven Doors Remove the door inner glass as follows Cleaning the DoorsRefit the door inner glass as follows Electrical Connections InstallationElectrical Requirements All cases adhere to routing details see figVentilation Final InstallationGeneral List of loose itemsTall Cabinet Ventilation 597mm Problem Check Something Wrong?Grilling is uneven Page Key Contacts For further product information 08701

N230E, E430E, R430E specifications

The Creda R430E, E430E, and N230E models represent a significant advancement in the realm of electric heating appliances, combining efficiency, user-friendliness, and modern aesthetics. These models are tailored to meet a variety of heating needs, making them suitable for both residential and light commercial applications.

One of the standout features of the Creda R430E, E430E, and N230E is their energy efficiency. These models are designed with advanced heating technologies that minimize energy consumption while maximizing heat output. This not only leads to lower energy bills for the user but also contributes to an environmentally friendly heating solution.

Each model is equipped with a built-in thermostat, allowing users to set their desired temperature with precision. This feature enhances user comfort, ensuring that spaces are heated to the desired levels without unnecessary energy waste. Additionally, these appliances incorporate programmable timers, enabling users to schedule heating in advance, further promoting energy efficiency and user convenience.

The Creda R430E, in particular, is known for its robust build quality and durability. Its design incorporates safety features such as overheat protection and a sturdy casing, ensuring that the unit remains safe to operate, even in busy environments. The E430E and N230E models also share this emphasis on safety, making them reliable choices for homes and other settings.

Another noteworthy characteristic of these models is their whisper-quiet operation. Unlike traditional heating systems, the Creda appliances operate silently, making them ideal for bedrooms, offices, and other quiet spaces. This attribute enhances the overall user experience, as there is no distracting noise associated with heating.

In terms of aesthetics, both the R430E and E430E models boast a sleek and modern design that effortlessly blends into any décor. Their compact size allows for flexible installation options, whether mounted on a wall or placed on the floor, ensuring that users can optimize their space.

Overall, the Creda R430E, E430E, and N230E models showcase a perfect balance of performance, safety, and aesthetic appeal. They represent a solid investment for individuals seeking reliable and efficient heating solutions, making them a preferred choice among homeowners and businesses alike.
Top Page Image Contents