Creda E430E, R430E, N230E manual General, Ventilation, Final Installation, List of loose items

Page 34

Installation

Important

It is essential that the lower cupboard is constructed in the manner illustrated i.e. having side, back, and roof panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2.Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3.Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Pozi Wash Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Pozi Wash Head No. 6 x 15mm screws.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents N230E / E430E / R430E Installation & User Instructions Creda Answer Centre 08701 54 64 Creda Answer Centre 08701 54 64Contents Disposal of your product Introduction89/336/EEC 73/23/EEC 92/31/EEC 93/68/EEC Safety Advice Safety InformationAlways Safety Information Never Features Grill Setting Control ControlsOven Timer Operation Timer Function Buttons Know Your TimerSymbols ClockfaceSetting the Time of DAY Setting the Minute MinderAuto Cooking Programmes Electronic Clock and Automatic Oven Timer Operation Other Notes on Timer Operation Top Oven Shelf Positioning for Grilling Grill Pan and HandleGrill Pan Food Grid and Anti-Splash Tray StepUsing the Top Oven for Solarplus Grilling For Half Grill Left hand side only Operation when using the Top Oven for GrillingGrillFull = Full Grill Function = Maximum Grill Setting Grill Controls ExampleSetting FoodConventional Grilling N230E Grill pan handleEasy Glide Shelf Using the Top Oven as a Convection OvenShelf Positioning Plate Warming Operation when using the Top Oven as a Convection OvenNever use the grill setting control a when warming plates Top Oven UtensilsUsing the Main Oven for Fan Cooking Main Oven Shelf Positioning for Fan OvenLight only Setting Using the Main Oven for Other FunctionsFan Only Setting Operation To assist in defrostingAdvantages of Slow cooking are Slow SettingPoints to consider when preparing food for Slow cooking OperationTemperature Conversion Chart Conventional Convection Fan Mark OvenOven Temperature Charts Meat Top Oven Convection CookingOven Temperature Charts Baking Baking General Cooking Results Not SatisfactoryGrill TOP Oven BakingHow Credaclean works Care and CleaningCredaclean Oven Liners E430E / N230E CleaningRemovable Grill Roof Panel not all models Cleaning GRILL, TOP Oven and Main OvenGrill Pan, Meat Pans & Oven Shelves Solarplus GrillHOW to Clean the Lamp Lens Replacement of the Oven LampOven Doors Remove the door inner glass as follows Cleaning the DoorsRefit the door inner glass as follows Electrical Connections InstallationElectrical Requirements All cases adhere to routing details see figVentilation Final InstallationGeneral List of loose itemsTall Cabinet Ventilation 597mm Problem Check Something Wrong?Grilling is uneven Page Key Contacts For further product information 08701

N230E, E430E, R430E specifications

The Creda R430E, E430E, and N230E models represent a significant advancement in the realm of electric heating appliances, combining efficiency, user-friendliness, and modern aesthetics. These models are tailored to meet a variety of heating needs, making them suitable for both residential and light commercial applications.

One of the standout features of the Creda R430E, E430E, and N230E is their energy efficiency. These models are designed with advanced heating technologies that minimize energy consumption while maximizing heat output. This not only leads to lower energy bills for the user but also contributes to an environmentally friendly heating solution.

Each model is equipped with a built-in thermostat, allowing users to set their desired temperature with precision. This feature enhances user comfort, ensuring that spaces are heated to the desired levels without unnecessary energy waste. Additionally, these appliances incorporate programmable timers, enabling users to schedule heating in advance, further promoting energy efficiency and user convenience.

The Creda R430E, in particular, is known for its robust build quality and durability. Its design incorporates safety features such as overheat protection and a sturdy casing, ensuring that the unit remains safe to operate, even in busy environments. The E430E and N230E models also share this emphasis on safety, making them reliable choices for homes and other settings.

Another noteworthy characteristic of these models is their whisper-quiet operation. Unlike traditional heating systems, the Creda appliances operate silently, making them ideal for bedrooms, offices, and other quiet spaces. This attribute enhances the overall user experience, as there is no distracting noise associated with heating.

In terms of aesthetics, both the R430E and E430E models boast a sleek and modern design that effortlessly blends into any décor. Their compact size allows for flexible installation options, whether mounted on a wall or placed on the floor, ensuring that users can optimize their space.

Overall, the Creda R430E, E430E, and N230E models showcase a perfect balance of performance, safety, and aesthetic appeal. They represent a solid investment for individuals seeking reliable and efficient heating solutions, making them a preferred choice among homeowners and businesses alike.
Top Page Image Contents