Whirlpool W10314956B Refrigerator Doors and Drawer, Connect to Refrigerator, To Replace Handles

Page 5

Connect to Refrigerator

1.Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2.Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a “P” clamp.

A

B

C

D

A. Copper tubing

C. Compression nut

B. “P” clamp

D. Compression sleeve

3.Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1.Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely fill the ice container.

Refrigerator Doors and Drawer

All graphics referenced in the following instructions are included later in this section after “Final Steps.”

Remove and Replace Handles

To Remove Handles:

1.Grasp the lower part of the handle firmly, slide the handle up and pull the handle straight out from the door. See Handle graphic.

To Replace Handles:

1.Position the handle so that the large holes in the mounting clips are down and align the holes with the door studs.

2.Rotate the handle so that the mounting clips are flat against the door and slide the handle down to engage. See Handle graphic.

Remove Doors and Hinges

IMPORTANT:

■Remove food and any adjustable door or utility bins from doors.

■Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

TOOLS NEEDED: ⁵⁄₁₆", ³⁄₈", ¹⁄₄" hex-head socket wrench, Torx®† T20 screwdriver, #2 Phillips screwdriver, and a flat-blade screwdriver.

1.Unplug refrigerator or disconnect power.

2.Remove the base grille. Grasp the grille firmly and pull it toward you.

3.Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

4.Remove top hinge cover from left side refrigerator door.

5.Disconnect the wiring plug located on top of the hinge by wedging a flat-blade screwdriver or your fingernail between the two sections. See Connections graphic.

6.Disconnect the water line by pulling back on the locking collar while pulling the water line out of the water line connector. See Connections graphic.

7.Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

8.Using a ³⁄₈" hex wrench, remove the leveling leg brackets from the bottom of the cabinet. Keep screws for later use.

†®TORX is a registered trademark of Textron Innovations Inc.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Refrigerator User Instructions Refrigerator SafetyClean Before Using Installation InstructionsUnpack the Refrigerator Before You Throw Away Your Old Refrigerator or FreezerRecommended Grounding Method LocationRequirementsElectrical Requirements Connect the Water Supply Water Supply RequirementsReverse Osmosis Water Supply Tools NeededConnect to Refrigerator Refrigerator Doors and DrawerRemove and Replace Handles To Remove Handles To Replace HandlesReplace Drawer Front Remove Drawer FrontReplace Doors and Hinges Remove and Replace Freezer DrawerBottom Hinges Using theControls Adjust the DoorsRefrigerator USE Opening and Closing DoorsCondition Temperature Adjustment Adjusting the ControlsAdditional Features Fast CoolWater Filter Status Light and Filter Reset Door Ajar AlarmCrisper Humidity Control Ice Maker and Ice Storage BinTo Dispense Ice Water Filter StatusLightTo Dispense Water Water Filtration System CleaningRefrigerator Care Changing the Light Bulb TroubleshootingRefrigerator Operation To Replace an Appliance BulbIce and Water Temperature and MoistureTemperature is too warm Water and ice dispenser will not operate properly Water Filter CertificationsApplication Guidelines/Water Supply Parameters Performance Data SheetItems Excluded from Warranty Limited WarrantyThis limited warranty does not cover Disclaimer of Implied WarrantiesRéfrigérateur Sécurité DU RéfrigérateurExigences demplacement Instructions D’INSTALLATIONDéballagedu réfrigérateur Avant de jeter votre vieux réfrigérateur ou congélateurSpécificationsélectriques Méthode recommandée de mise à la terreSpécifications del’alimentationen eau Alimentation en eau par osmose inverseRaccordement de la canalisation deau Achever l’installationRaccordement à une canalisation d’eau Raccordement au réfrigérateurDépose de la façade du tiroir Réinstallation de la façade du tiroirPortes et tiroir duréfrigérateur Charnières inférieures Utilisation DU Réfrigérateur Utilisation des commandesAjustement desportes Ouverture et fermeture des portesFast Cool glace rapides Ajustement des commandesCondition Ajustement DE LA Température Refroidissement On/Off marche/arrêtMachine à glaçons et bac d’entreposage Alarme de porte entrouverteTémoin lumineux du filtre à eau et réinstallation du filtre Distribution d’eau Distributeurs d’eau et de glaçonsDistribution de glace RemarquesTémoin lumineux de l’état dufiltre à eau Entretien DU RéfrigérateurSystème defiltrationde leau NettoyageRemplacement del’ampoule d’éclairage Fonctionnement duréfrigérateur DépannageLe réfrigérateur ne fonctionne pas Le moteur semble trop tournerLes portes sont difficiles à ouvrir Température et humiditéGlaçons et eau Remplacer le filtre ou le réinstaller correctement Système de filtration d’eau intérieur Feuille DE Données SUR LA PerformanceGarantie Limitée Garantie DE Gros Appareil Ménager Whirlpool CorporationÉléments Exclus DE LA Garantie La présente garantie limitée ne couvre pasPage Page Page Page Page Whirlpool Corporation All rights reserved W10314956B SP PN W10314957B

W10314956B specifications

The Whirlpool W10314956B is a highly regarded microwave hood combination that offers a blend of modern convenience and essential cooking features. Designed to fit seamlessly into contemporary kitchens, this appliance functions as both a microwave and a range hood, making it an ideal choice for multitasking and saving space.

One of the standout features of the Whirlpool W10314956B is its powerful ventilation system. With a fan capable of reaching up to 400 CFM, it efficiently removes smoke, steam, and odors from your kitchen during cooking. This is further enhanced by its two speed settings, allowing users to select the appropriate fan speed based on their cooking needs. The grease filter is dishwasher safe, ensuring easy maintenance and optimal performance over time.

In terms of microwave functionality, the W10314956B boasts a spacious interior that accommodates a variety of plate sizes and cooking containers. With a generous microwave power of 1,800 watts, it delivers quick and even heating. The microwave features multiple cooking options, including one-touch settings for popcorn, baked potatoes, and other popular food items. The sensor cooking technology takes the guesswork out of food preparation by automatically adjusting cooking time based on humidity levels, ensuring perfectly cooked meals every time.

The appliance is also equipped with a sleek digital control panel that is user-friendly and intuitive. The bright LED lighting illuminates the cooktop area, enhancing visibility while cooking. This is especially beneficial for late-night meals or when working with intricate recipes that require precision.

Another notable characteristic of the Whirlpool W10314956B is its aesthetic design, which complements a variety of kitchen decors. Its stainless steel finish is not only stylish but also resistant to fingerprints and smudges, ensuring that your kitchen looks clean and polished at all times. Additionally, the compact design allows it to fit under cabinets without taking up excessive space, making it a practical solution for smaller kitchens.

Overall, the Whirlpool W10314956B is a versatile and efficient kitchen appliance that combines the functionality of a microwave with the benefits of a range hood. With its powerful performance, user-friendly features, and sleek design, it is an excellent choice for homeowners looking to optimize their cooking experiences. Whether you are reheating leftovers or cooking a gourmet meal, this microwave hood combination offers the reliability and performance that modern kitchens demand.
Top Page Image Contents