Whirlpool W10214130A Connect the Water Supply, Reverse Osmosis Water Supply, Style

Page 4

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207 and 827 kPa) is required to operate the ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the ice maker is still not operating properly:

■Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

■Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect the Water Supply

(on somemodels)

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

1.Unplug refrigerator or disconnect power.

2.Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3.Locate a ¹⁄₂" to 1¹⁄₄" (1.27 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

■Make sure it is a cold water pipe.

■Horizontal pipe will work, but drill on the top side of the pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4.Determine the length of copper tubing you will need. Measure from the connection on lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5.Using a cordless drill, drill a ¹⁄₄" hole in the cold water pipe you have selected.

 

A

G

B

 

 

C

F E

D

A. Cold water pipe

E. Compression sleeve

B. Pipe clamp

F. Shutoff valve

C. Copper tubing

G. Packing nut

D. Compression nut

 

6.Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the ¹⁄₄" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7.Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8.Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

NOTE: On kit models, assemble water valve to refrigerator per kit instructions.

Style 1

1.Unplug refrigerator or disconnect power.

2.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten.

3.Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help avoid damage to the tubing when the refrigerator is pushed back against the wall.

4.Turn shutoff valve ON.

5.Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

 

A

 

B

 

C

 

D

 

E

A. Tube clamp

D. Compression nut

B. Tube clamp screw

E. Valve inlet

C. Copper tubing

 

6.The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

Style 2

1.Unplug refrigerator or disconnect power.

2.Disconnect the tube clamp on the back of the product and insert the copper tubing through the clamp as shown.

3.Attach the copper tube to the valve inlet using a compression nut and sleeve as shown.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Refrigerator Safety Refrigerator User InstructionsUnpack the Refrigerator Installation InstructionsBefore You Throw Away Your Old Refrigerator or Freezer Clean Before Using LocationRequirementsElectrical Requirements Water Supply RequirementsReverse Osmosis Water Supply Connect the Water SupplyStyle Refrigerator Doors Style 1 StandardRemove Doors and Hinges Reverse Doors optionalStyle 2 Contoured Door Removal Replacement Door Swing Reversal optional Door Swing Reversal optional Adjust the Doors Using theControlsMid-setting Adjusting ControlsCleaning To Clean Your RefrigeratorRefrigerator Care Ice MakerChanging theLight Bulbs TroubleshootingRefrigerator Operation Temperature and Moisture Temperature is too warmIce and Water Door will not close completelyWhirlpool Corporation Major Appliance Warranty This limited warranty does not coverSécurité DU Réfrigérateur RéfrigérateurInstructions D’INSTALLATION Déballage duréfrigérateurAvant de jeter votre vieux réfrigérateur ou congélateur Nettoyage avant l’utilisationExigences d’emplacement Méthode recommandée de mise à la terreSpécifications électriques Spécifications del’alimentationen eauRaccordement de la canalisation d’eau Alimentation en eau par osmose inversePression de leau Raccordement à une canalisation d’eauAchever l’installation Portes duréfrigérateurDémontage Portes et charnières Inversion des portes facultatifStyle 2 Contour Inversion du sens douverture de la porte option Style 2 Contour Utilisation des commandes Utilisation DU RéfrigérateurAjustement desportes Réglage moyenAjustement des réglages de commande Machine à glaçonsMise en marche/arrêt de la machine à glaçons Taux de production de glaçonsRemplacement des ampoules d’éclairage Entretien DU RéfrigérateurNettoyage Pour nettoyer le réfrigérateurDépannage Fonctionnement du réfrigérateurGlaçons et eau Température et humiditéIl y a une accumulation dhumidité à lintérieur Garantie DE Gros Appareil Ménager Whirlpool Corporation La présente garantie limitée ne couvre pasW10214130A SP PN W10214256A Whirlpool Corporation All rights reserved

W10214130A specifications

The Whirlpool W10214130A is a highly efficient appliance designed to enhance the functionality of modern kitchens. This versatile kitchen appliance embodies the brand’s commitment to quality and innovation, making it a staple in many households. One of the standout features of the W10214130A is its advanced technology aimed at improving user experience and maximizing convenience.

First and foremost, this model is equipped with a powerful motor that ensures fast and efficient operation, reducing preparation time for various tasks. Whether you are blending, mixing, or kneading, the robust motor provides consistent performance across different settings. The appliance also boasts multiple speed settings, allowing users to customize the intensity for precise results according to the specific task at hand.

Another notable characteristic of the W10214130A is its durability. The appliance is constructed with high-quality materials that are resistant to wear and tear, ensuring longevity and reliable service. The stainless steel components not only enhance the durability but also add an element of sleekness and modernity to the kitchen aesthetic.

Ease of cleaning is a major consideration in kitchen appliances, and the W10214130A excels in this area as well. Many parts of the appliance can be disassembled and are dishwasher safe, making post-use cleanup a breeze.

Moreover, the design of this appliance emphasizes safety and user-friendliness. It includes a secure locking mechanism that ensures safety during operation, especially when dealing with high speeds. This feature is particularly important for families with children, providing peace of mind while using the appliance in a bustling kitchen environment.

The Whirlpool W10214130A also prioritizes energy efficiency, which aligns with contemporary sustainability practices. By consuming low energy while still delivering powerful performance, it helps reduce electricity bills and minimize environmental impact.

In summary, the Whirlpool W10214130A is a blend of innovative technology, durable design, and user-friendly features. Its combination of versatility, safety, and energy efficiency makes it an excellent addition to any modern kitchen, catering to the needs of home cooks and professional chefs alike.
Top Page Image Contents