Whirlpool IUD8000R Cycle Status Indicators, Drying System, Overfill Protection Float, Lock, Clean

Page 12
Lock

Lock

Use the lock to prevent unintended use of the dishwasher. You can also use the lock feature to prevent unintended cycle or option changes during a cycle.

When the lock is lit, all buttons are disabled.

NOTES:

The dishwasher door can be opened while the controls are locked.

You can turn on the lock while the dishwasher is running. If you open the door, unlock the controls and press START/ RESUME to restart. You can lock controls again, if desired.

To turn on the lock

Press and hold HEATED DRY for 4 seconds. The lock glows.

If you press any pad while your dishwasher is locked, the light flashes 3 times and the selection is ignored.

To turn off the lock

Press and hold HEATED DRY for 4 seconds. The light turns off.

Delay start

Select this option to run your dishwasher at a later time or during off-peak hours. You can add items to the load anytime during the delay countdown. After adding items, close the door firmly until it latches. The delay countdown will not continue if the door is not latched. Press START/RESUME. If the door is unlatched, the Start/Resume indicator flashes. The delay countdown stops until you latch the door and press START/RESUME.

To delay the start

1.Press DELAY for a 4-hour delay. The number above or to the left of the 4 Hour Delay pad glows.

2.Select a wash cycle and option or skip to Step 3 to use the cycle and options selected for last cycle.

3.Press START/RESUME. (The door must be closed.) The delay countdown starts, and the cycle will begin after 4 hours.

NOTES:

To cancel the delay and cycle, press CANCEL/DRAIN.

To cancel the delay and start the cycle, press START/ RESUME.

Cycle Status Indicators

Follow the progress of your dishwasher with the Cycle Status indicators.

NOTE: Your model may have some or all of the indicators shown above.

Clean

Clean glows when a cycle is finished. The light turns off when you open and close the door or press any button.

Sanitized

If you select Sanitize Rinse, Sanitized glows when the Sanitize Rinse option is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted, or the water could not be heated to the required temperature. The light goes off when you open and close the door or press any button.

Drying System

During drying, you can see steam escaping through the vent at the upper left corner of the door. This is normal as the heat dries your dishes.

IMPORTANT: The vapor is hot. Do not touch the vent during drying.

Overfill Protection Float

The overfill protection float (in the front right corner of the dishwasher tub) keeps the dishwasher from overfilling. It must be in place for the dishwasher to operate.

Check under the float for objects that may keep the protector from moving up or down.

12

Image 12
Contents Model/Modèle IUD8000R DISHWASHERLAVE-VAISSELLE Use & Care GuideTABLE DES MATIÈRES TABLE OF CONTENTSDISHWASHER SAFETY Before Using Your Dishwasher PARTS AND FEATURES Control PanelUsing Your New Dishwasher START-UPGUIDEDISHWASHER LOADING Stopping Your DishwasherLoading Bottom Rack Loading Silverware BasketDISHWASHER USE Detergent DispenserFilling the dispenser How much detergent to useRinse aid setting To adjust the settingfill Rinse Aid DispenserCycle Selection Charts Pots & PansNormal LightCanceling a Cycle Changing a Cycle or SettingTo clear the indicators Adding Items During a CycleCycle Status Indicators CleanDrying System Overfill Protection FloatWASHING SPECIAL ITEMS Cleaning Cleaning the exteriorCleaning the interior To clean interiorTROUBLESHOOTING Dishes are not completely cleanDishwasher is not operating properly Spots and stains on dishes Dishes do not dry completelyDishes are damaged during a cycle NoisesASSISTANCE OR SERVICE If you need replacement partsFor service in Canada In the U.S.AWHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY ONE YEAR LIMITED WARRANTYITEMS WHIRLPOOL WILL NOT PAY FOR callLA SÉCURITÉ DU LAVE-VAISSELLE DANGERAVERTISSEMENT IMPORTANTES INSTRUCTIONS DE SÉCURITÉAvant d’utiliser le lave-vaisselle Pour un lave-vaissellebranché en permanenceINSTRUCTIONS DE MISE À LA TERRE CONSERVEZ CES INSTRUCTIONSTableau de commande PIÈCES ET CARACTÉRISTIQUESGUIDE DE MISE EN MARCHE CHARGEMENT DU LAVE-VAISSELLEUtilisation de votre nouveau lave-vaisselle Arrêt du lave-vaisselleChargement du panier supérieur Chargement du panier inférieurUTILISATION DU LAVE-VAISSELLE Chargement du panier à couvertsDistributeur de détergent Remplissage du distributeurDistributeur dagent de rinçage Quantité de détergent à utiliserConseils d’efficacité pour le lave-vaisselle Tableaux de sélection de programmesRéglage de la quantité dagent de rinçage Conseils d’efficacité supplémentairesAnnulation d’un programme Pots & Pans/casserolesShort Wash/lavage bref Light/légerChangement d’un programme ou réglage Addition de vaisselle durant un programmeSélection d’options Durant le premier remplissage d’un programmePour désactiver le verrouillage des commandes Clean propreIndicateurs d’état d’avancement du programme Système de séchageLAVAGE D’ARTICLES SPÉCIAUX ENTRETIEN DU LAVE-VAISSELLE NettoyageDispositif anti-refoulement RemisageDÉPANNAGE Le lave-vaissellene fonctionne pas correctementVaisselle pas complètement nettoyée Présence de taches sur la vaisselle Vaisselle pas complètement sècheVaisselle endommagée au cours d’un programme BruitsASSISTANCE OU SERVICE Pour service au CanadaAux États-Unis Au CanadaGARANTIE DES GROS APPAREILS MÉNAGERS WHIRLPOOL CORPORATIONGARANTIE LIMITÉE DE UN AN WHIRLPOOL NE PRENDRA PAS EN CHARGEAll rights reserved Tous droits réservés