Whirlpool ET22ZM manual Changing the light bulb, Automatic ice maket, Removing the base grille

Page 7

Changing the light bulb...

WARNING: Before removing the light shield for cleaning or for replacing the bulb, either unplug refrigerator or discon-

nect electricity leading to re- frigerator at the main power supply. Shock and injury can occur if elec- tricity remains connected.

Push in the Center;

Pull Down.

Push lightly on the top center of the light shield until the notched iab unhooks from the control panel Pull down on the shield until the tab clears the con- trol panel

LIH the back hooks oui of their slots Replace with a 40-watt appliance bulb Replace light shteld in reverse order

Automatic ice maket..

The automatic Ice maker ISin the freezer section of your refrigerator. The following things should be known for proper Ice maker use

lThe ON OFF lever ISa wire signal arrr

Down for making ice automat~cal’i Up to shut off the ice maker

l Shake the bin occasionally to keep &oes sey;c rated, and to obtain Increased storage capac~+r

On

Lower

Signal

 

\

Raise

Signal

Arm

to

Start

It

Arm to Stop Ice Maker

l It

IS normal

for Ice c’escents

tc be

attached

Lr -J

corner They will break apart easllv

l You will hear water ruqnlng w?en ice maker i working You’ll hear Ice fall into: ti‘e tl ‘I ?\I~I t -.I

l

l

l

l

l

l

these sounds bother you

The ice maker will not operate until the freezer IS cold enough to make ice This can take overnight Because of new plumbing connectIons, the first Ice may be &colored or off-flavored Discard the first few batches of Ice

If Ice ISnot being made fasi enough and more ice ISneeded, turn the Temperature Control toward a higher number. Wait a day and, If necessary, turn the Air Control toward A

If you remove the Ice bin, raise the signal arm to snu+ off the ice maker When you return the bin. push It all the way in and lower ihe arm to the ON position

If cubes are stored too long, they may develop an off-flavor like stale water Throw them away They WIII oe replaced Cubes In the Ice bin can also become smaller by evaporation

Good water quality ISimportant for good Ice quality I+IS not recommended that the Ice maker be con- nected to a softened water supply. Water softener chemicals such as salt from a malfunct~onlng soft- ener can damage the Ice maker mold and lead to poor quality ice If a softened water supply cannot be avoided, then It ISimportant that the water soft- ener be well maIntaIned and operating properly

Removing the base grille...

Support labs

To replace:

? Liqe up grille support tabs with metal clips

L Pull grille outwards as shown? Push,firmly to snap tnto place 3 Do not remove Tech sheet fas’ened behlno gril c? 3 Close the doors

Image 7
Contents NO-FROST Refrigerator Freezer ‘lome rot &erc tcrs no &I Slgned tc CIO Contents To remove any remaining glue Install properlyHousehold Refrigerator Usage These Settings Should Be about RightGlve Refrigerator Time to cool down com Pletely betore addlng food. This may take sevRemoving the crispers Adjusting the refrigerator shelvesAdjusting the door bins Moving the meat panAutomatic ice maket Changing the light bulbRemoving the base grille Probable Causes Sounds you may hearEnergy saving tips Possible SoundsPart Cleaning chartHow to clean CleansersApproxlmate lime StoragechartforfreshanocureomeatWays1 Freezing & Storing Frozen Foods Freezing Baked Goods-Wrap baked breads Meat FoodstoragechartFruits VegetablesVacation If you need assistance If you need serviceIf you have a problem Before calling for assistanceWhirlpa