TC electronic SDN BHD 48 user manual Parameters

Page 29

INTEGRATOR

Installation

The Integrator plug-in is automatically installed along with the TC Near control panel.

Parameters

1Device

Your setup may include several Konnekt units. Select the Konnekt unit to which you are about to integrate an external effect.

21st audio channel

Your DAW detects audio channels on the Studio Konnekt 48 and labels these automatically.

If you insert Integrator on a mono track it will open as a mono plug-in. On a stereo track it will open as a stereo plug-in. In stereo you will select channels by selecting the only first of the two. In the illustration on the previous page, main out 1/2 is selected even though the label says “main out 1”.

3Calibrate

Integrating external digital devices will introduce a short latency, but your host application can be set up to compensate for this using the Integrator calibrate function.

Press CALIBRATE to measure the total roundtrip latency including the latency within the external device.

The latency compensation feature of the host application will then make sure to compensate for this latency.

This procedure should be carried out on each audio track where Integrator is inserted.

4Test & Auto

To verify that all cables to external units are properly connected, a pink noise test signal can be sent to left/right channels. Use L or R to send to left/right channels individually. You may also press AUTO. Then Integrator will send a pink noise signal that alternates between Left and Right channels.

To prevent sending a test signal at max level (0 dB) to the selected “1st audio channel” the test signal

level will automatically be turned down when pressing L, R or AUTO. However, you may change the test signal level by grabbing the yellow triangle and moving it up/down. The set level for this instance of the Integrator will be remembered.

5/6 Send/Return levels

By moving the two yellow triangles next to the Send and Return meters you can set the Integrators send/return levels. Adjust these according to the I/O levels on the sending device. Meter indications should be as close to 0 dB as possible without overloading.

27

Image 29
Contents User’s Manual Page Service Important Safety InstructionsFor Customers in Canada EMC / EMI & Certificate of ConformityTable of Contents 24/8 channel digital mixer with double precision summing IntroductionSpeaker management based on AIR technology World-class DSP effectsComputer Requirements Setup NotesFront Panel Phantom Power +48V FireWire/Power LED indicatorMeters Valid LEDRear Panel Remote FireWire connectorsControl Panel Mixer Tabs Konnekt select tabsAdd Channel Removing a channelAll Channels Linked Unlinked Monitor mix on/off Output sectionTalkback function Talkback microphone Selecting talkback microphoneDim level Fabrik C studio even on talkbackTalkback routing Talk buttonMaster Level Channel Setup Optical Format Stand-Alone Clock SettingsInput section Introduction basics Routing Channels to OutputsLink button Source selectDSP DAWSpeaker or Line level ? Assigned toBass management Levels Bass Management16 + 17 High Pass & Low Pass Setup Examples Studio Recording & Monitoring Features used in this setup Mainl LINE8 Setup Examples Bass Management & IntegrationSetup Examples Bass Management & Integration Integrator Parameters Objects Integrating external hardware with your DAWConnections TC Near WDM Setting upKonnekt WDM Driver Clock System SettingsBuffer Size Example 2 Studio Konnekt 48 Jitter Elimination Prevent from changing sample rate DPC Safety Buffers PC onlySample Rate Check for update +7 Clock Recovery and StatusStudio Kontrol Optional Studio Kontrol Speaker SET select Encoder and LightringAUX 2 Shift + Effect Momentary or latchingCH on/off Channel on/off Studio ControlTuner Shift + Talk Studio Control Remote Midi Effect buttonReverb TIME/DECAY Introduction Main featuresFabrik C Studio Band compression on Bass Fabrik COverview Full-band or 3-band compression? EQ Section LimiterDe-Esser HeadroomSignal Flow Full-band mode Signal Flow 3-band modeAdjusting BW/TYPE Adjusting Frequency and gainBands On/Off Grab handle to select BypassNotch Filter Narrow type Filter typesType GainCompression Source selectionVia the drop down menu Source Selection Band and Full-band modes Gain Gain ControlBand mode only Level Level Control Band mode only Compressor Control Compressor controlGrid Adjusting Parameters Compressor sectionFull-band mode Amount ThresholdRouting modes Overview Fabrik R StudioReverb Types Meters Tweak sectionLevel Color Modulation Time Overload indicationTime Modulation PreDelayDecay Modulation RateColor Kill Dry Kill wet Additional parametersIn/Out Preset Handling Preset Handling Fabrik C & Fabrik RPreset File Menu P1, P2 & P3Page Basic operation Resonance FilterOutput FilterCommunication Example Cross fade between two tracks Tuner Indication TunerPlay tone Mode selectorPitch Scale modesOutputs Appendix Asio Channel NamesMonitor Speaker Studio Konnekt 48 Signal FlowShortcut keys Appendix FAQReset to Default Firmware Update & Resetto DefaultCheck for updates VersionsTHD Technical Specifications

48 specifications

TC Electronic SDN BHD 48 is a cutting-edge digital signal processing system designed to deliver high-quality audio solutions for various applications including live sound, broadcasting, and installation projects. This advanced system is a testament to TC Electronic’s commitment to innovation and excellence in the audio industry.

One of the standout features of the SDN BHD 48 is its unique digital audio processing engine which utilizes advanced algorithms to achieve superior sound quality. This engine allows users to manipulate and enhance audio signals in real-time, resulting in exceptional sonic clarity and detail. The system supports up to 48 channels of processing, making it versatile enough for any large-scale audio operation.

SDN BHD 48 comes equipped with an intuitive user interface that provides easy access to a plethora of controls and settings. Users can navigate through the system seamlessly, making adjustments on the fly. This user-centric design ensures that audio engineers can focus more on the sound rather than getting bogged down in complex operational tasks.

The system also incorporates state-of-the-art connectivity options, including a robust networked audio protocol which allows for seamless integration with other digital devices. This opens the door to myriad configuration possibilities and enables users to customize their setup according to specific needs. The SDN BHD 48 supports various protocols such as AES67 and Ravenna, ensuring compatibility with a wide range of equipment.

In terms of signal routing, SDN BHD 48 offers flexible options that allow for both simple and complex configurations. This means that users can easily set up audio signals for different areas or zones, making it ideal for installations in large venues like concert halls and hotels.

Robustness is also a key characteristic of the SDN BHD 48. Built to withstand the rigors of touring and professional use, it boasts a rugged chassis and high-quality components that enhance durability. Additionally, the system provides extensive monitoring and diagnostic capabilities so users can ensure optimal performance and troubleshoot issues quickly.

In summary, TC Electronic SDN BHD 48 merges state-of-the-art audio technology with user-friendly features, making it an indispensable tool for professionals who demand high performance from their audio systems. With its advanced processing capabilities, connectivity options, and robust design, it stands out as a leading solution in the competitive audio technology market.