Sunfire TGR-401-230 manual Zone 2 Connections, Zone 2 OSD menus

Zone 2 Connections

As an alternative to using the TGR-
401's internal amplifiers to run your	Connection to IR
Zone 2 speakers, you could use an
external power amplifier. Connect the	receiver in Zone 2
amplifier's line-level inputs to the TGR-
401 Zone 2 stereo outputs.

Speaker-level audio signals	+		+
	TO
From: Receiver speaker outputs		LEFT
	ZONE 2		TO RIGHT
To: Zone 2 speaker inputs
	SPEAKER
			ZONE 2
			SPEAKER

CHAPTER 2

Zone 2 OSD menus

MAIN MENU

TRIMS

TONE CONTROLS

MODES

PRESETS

SETUP

SETUP	CHOICES
INPUTS
SPEAKERS
VIDEO
MAIN ZONE
ZONE 2
CONTROL
DIGITAL OUT	DN MIX/THRU
DIMMER	LOW/MEDIUM/HIGH
ZONE 2			CHOICES
FIXED VOLUME		N	N, 0.0 - 100.0
PWR UP MAX VOL		60.0	0.0 - 100.0
PWR UP MIN VOL		0.0	0.0-100.0 MUST BE LESS THAN POWER
			UP MAX VOLUME
MAX VOLUME		100.0	0.0-100.0 MUST BE MORE THAN POWER
			UP MAX VOLUME
PWR UP SOURCE		LAST	LAST, INPUT 1,INPUT 2, ... INPUT 8, AM,

Zone 2 can play stereo analog sources independently of the Main Zone, or play the same source. Zone 2 can only play a digital source if the Main Zone is playing the same source.

If you want the TGR-401 speaker- level outputs to run your Zone 2 speakers, under the OSD Binding Post menu, set "POWERED Z2" to ON.

Speaker wires are connected to the speaker outputs as shown above, and are run out to Zone 2 speakers, located in another room or area of your house.

If you have an external power amplifier to run your Zone 2 speakers, connect the TGR-401 Zone 2 line-lev- el stereo outputs to the inputs of your amplifier. Connect your Zone 2 speak- ers to the amplifier with speaker wire. This method provides full-time 7.1 for the home theater, plus an amplified Zone 2.

The wire from an optional IR sensor is shown connected to the TGR-401 Zone 2 IR input. The TGR-401 is com- patible with most makes of IR sensors and equipment.

The sensor can be located in a suitable area of Zone 2, allowing you complete control of the volume and source selection. Zone 2 can also be controlled from the front panel, using the remote's Zone 2 buttons.

The optional Olé-2SF Film Interac- tive touchpads are preconfigured to operate Zone 2. They connect to ei- ther the TP1 or TP2 connectors on the TGR-401 rear panel. The touchpads allow you to control the source selec- tion, volume, bass, and treble. Also, they will pass IR commands back to the TGR-401, as they have an internal IR receiver. For custom programming, please contact your Sunfire dealer.

		FM, SIRIUS, FRONT
BASS	0	+14 TO -14, 2 DB STEPS
TREBLE	0	+14 TO -14, 2 DB STEPS
BALANCE	0	-20 TO +20, 1 DB STEPS
SPEAKERS
AUTO SETUP
SPEAKER SIZE
DISTANCE
LEVEL CALIBRATION
EQ
BINDING POSTS
BINDING POSTS			CHOICES
AMP SECTION	ON		ON, OFF
FRONT	ON		ON, OFF
SURROUND	ON		ON, OFF
CFG POST	OFF		OFF, FRONT, SURR
POWERED Z2	OFF		ON/OFF

The ZONE 2 menu allows you to:

•Set a fixed volume

•Set max and min volume at Zone 2 power-up

•Set a maximum volume

•Select a source to play at Zone 2 power-up

•Adjust bass, treble and balance

The Binding Posts menu allows you to:

•Power the Zone 2 speakers or

•Power the Main Zone surround back speakers

User's Manual

23