Sunfire IV manual NEC National Electrical Code

Page 3

SAFETY

15.To prevent electric shock, do not use this polarized plug with an exten- sion cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

Pour préevenir les chocs électriques ne pas utiliser cette fi che polariseé avec un prolongateur, un prise de courant ou une autre sortie de cou- rant, sauf si les lames peuvent être insérées à fond sans laisser aucune parIVe à découvert.

16.Grounding or Polarization — Precautions should be taken so that the grounding or polarization means of the Component is not defeated.

This apparatus does not exceed the Class A/Class B (whichever is ap- plicable) limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Ca- nadian Department of Communications.

ATTENTION — Le présent appar- eil numérique n'émet pas de bruits radioélectriques dépassant las limites applicables aux appareils numériques de class A/de class B (selon le cas) prescrites dans le règlement sur le brouillage radioélectrique édicté par les ministere des communications du Canada.

WARNING – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRO-

DUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO NATIONAL ELECTRICAL CODE INSTRUCTIONS CONTAINED IN ARTICLE 810—“RADIO AND TELEVISION EQUIPMENT”

GROUND CLAMP

ANTENNA

LEAD IN WIRE

GROUND CLAMPS

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

SERVICE(NEC SECTION 810-21)

ENTRANCE

EQUIPMENT

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC NATIONAL ELECTRICAL CODE.

NOTE TO CATV INSTALLER

This reminder is to call the CATV system installer's attention to Article 820-40 of the NEC that provides guide- lines for proper grounding and in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

OUTSIDE ANTENNA GROUNDING

If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the lead-in wire to an antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure above.

3

User's Manual

Image 3
Contents Theater Grand Safety Instructions NEC National Electrical Code Contents Introduction Features Remote FeaturesUnpacking Main OverviewQuick Start Guide TgivExit Further Information Front Panel Features Illuminated Logo Panel PowerTuner Presets LevelRear Panel Features AM Antenna RS-232 PortXLR Audio Outputs FM AntennaInstallation Analog audio and composite video System Confi gurationsRand Digital audio and component video connectionsDigital LD connections external RF Demodulator and S-VideoGrand VCR connections analog audio and composite videoAM Loop Antenna CD and Antenna connectionsTurntable connections Tape Player connections Grand Channel Input connections analog audioAmplifi er connections Zone 2 connections Remote Control ENT Operating the Tgiv with the RemoteZone Main AudioPRO Remote SetupLearn Remote SetupMacro Recal RecallOn Screen Display OSD OSD ActivationQuick Information OSD Menus Trim and Tone Menus Trims MenuTone Menu Pro Logic IIx Menu Modemusic Center Width Panorama on DimensionModes Menu Modes MenuInput Menus Input Confi guration MenusInput Menus Tuner Preset Menus Tuner Preset MenuPreset procedure Main Zone and Zone 2 Menu Zone 2 MenuMain Zone Menu Video Menu Video, Software and Control MenusSoftware Menu Control MenuSpeaker Size Menu Speaker Size MenuSpeaker Position Speaker Position MenuSpeaker Calibration Speaker Calibration MenuCrossover Crossover adjustment Subwoofer ModeSpeaker Crossover Menu SpeakersUsing the Tgiv Bass ManagementVideo Conversion Surround Modes for 2-Channel Sources Dolby PRO Logic IIDTS Neo6 Surround Modes for Multi-Channel Sources DTSDTS ES Tuner Operation Recording Recording to a Tape PlayerRecording to a VCR Turning on Zone IndicatorsZone 2 Operation ConnectionsSoftware Upgrade Software Revision List Holographic ImageSoftware CD Center speaker Speaker PlacementAppendix Front SpeakersSubwoofer Location Side-Axis SpeakersSurround speakers Surround Back SpeakersRS-232 Port Same AM station can be heard at different frequencies Troubleshooting GuideNo Dolby Digital, DTS playback Your amplifiers shut down often Remote Control Codes Tape Decks TelevisionsVCRs Video Settings Tone SettingsZone Settings Mode SettingsSpecifi cations Service Assistance Limited WarrantyManual part number 913-107-00 Rev B