Warming Drawer Use & Care | 7 |
wolfappliance.com
Electronic Controls
PRESET PROGRAMMING
Preset temperatures and time settings can be adjusted for
the 
, 
, 
and 
PRESETS.
The 
temperature range is 
, 
and 
PRESETS can be adjusted from
TO ADJUST PRESET TEMPERATURE AND TIME SETTING:
1)Warming drawer must be OFF.
2)Touch 
.
3)Touch and hold the desired PRESET, 
, 
, 
or 
for 5 seconds. The word TIMER will illuminate and “4:00” will flash in the LCD display along with the
temperature. Adjustments to the settings should be made within 30 seconds. The unit will exit the preset programming mode if no adjustment is made within this time.
4)To adjust the temperature, touch and hold the 
arrow to increase or the 
arrow to decrease the temperature until the desired preset temperature is
shown in the LCD display.
5)To adjust the time setting, touch and hold the 
arrow to increase or the 
arrow to decrease the time until the desired preset time setting is shown in
the LCD display.
6)Touch and hold the adjusted PRESET again for 5 seconds. Three quick tones will signify that settings for the PRESET have been changed. If 30 seconds elapse before you touch and hold the PRESET, the unit will exit the preset programming mode with no adjustments made.
Sabbath Mode
Sabbath mode is for certain religious observances where some warming drawer functions need to be turned off. In Sabbath mode, the automatic
TO INITIATE SABBATH MODE:
1)Warming drawer must be OFF.
2)Touch and hold 
for 5 seconds. The word “Sab” will flash in the LCD display after 5 seconds.
3)While “Sab” is flashing, select one of the PRESETS or
set the temperature with the 
or 
arrow
pads. Touch the 
arrow to increase the tempera-
ture and the 
arrow to decrease the temperature. Two tones will signify that the Sabbath mode has been
initiated.
4)In Sabbath mode, the warming drawer will operate
continuously until 
is touched. The word ON will remain illuminated in the LCD display all the while the
unit is in Sabbath mode. No other
5)Touch 
to shut off the warming drawer and exit Sabbath mode.
When Sabbath mode is initiated, the automatic
by touching 
.
Control Panel Backlighting
The Wolf warming drawer has three options for control panel backlighting; backlight off in Sabbath, backlight on in Sabbath and backlight off in all modes. The backlight defaults to ON in normal use and OFF in Sabbath mode.
TO CHANGE CONTROL PANEL BACKLIGHTING:
1)Warming drawer must be OFF.
2)Touch and hold 
arrow and 
arrow for 5 seconds. The current backlight setting will appear in
the LCD display.
3)Use the 
arrow to scroll through the three back- light options; backlight off in Sabbath, backlight on in
Sabbath (50% power), and backlight off in all modes. A selection should be made within 30 seconds. The unit will default to the current backlight setting if a new selection is not made within this time.
4)With the desired backlight setting selected, touch 
to save the setting.
Temperature Display
The warming drawer temperature display can be changed from Fahrenheit (F) to Celsius (C) or vice versa.
TO CHANGE TEMPERATURE DISPLAY:
1)Warming drawer must be OFF.
2)Touch and hold both the 
and 
arrows for 5 seconds.
3)After 5 seconds, the unit will beep, the backlighting will turn on, and either F or C will appear, depending on the current display setting.
4)Touch the 
or 
arrow to select either Fahrenheit (F) or Celsius (C).
5)With the desired temperature display selected, touch 
to save the setting.
Before Using for the First Time
Remove all literature and packaging materials from inside the warming drawer.
Clean your warming drawer thoroughly with hot water and a mild detergent. Rinse and dry with a soft cloth. This removes residual oil and grease left on the surface from the manufacturing process.
Apply a stainless steel polish to protect the finish and add luster to the exterior of your warming drawer. Refer to cleaning and care recommendations on page 9.