Waterford Precision Cycles Glass Island Hood manual General Guidelines Maintenance, Installation

Page 3

GENERAL GUIDELINES

 

MAINTENANCE

 

 

 

Before installing and /or using the cooker hood, please read these instructions carefully.

Before installing the cooker hood make sure the volt- age (V), frequency (Hz) indicated on the serial num- ber plate and specifications on the rating plate on the inside of the cooker hood correspond to the voltage and frequency of the mains supply.

INSTALLATION

The cooker hood must not be installed and connect- ed to flues where other appliances are installed and which run off other energy supplies other than elec- tricity (water heaters - boilers - cookers, range/gas etc). The extraction hood requires a 125mm extrac- tion pipe connected directly to the outside with an opening of a minimum cross section of 150cm2.

The hood must be installed with a distance of 650- 750mm between the cooker top/hob and the extrac- tion hood. The cooker hood must not be installed above cookers with eye-level grills.

ELECTRICAL CONNECTION

This cooker hood is designed for permanent fixture. Connect to mains supply. Check voltage and fre- quency given on the rating plate located on the inside of the hood. Connect the mains cable to a power socket or to a double pole switch with a con- tact gap of at least 3mm. The mains cable (type H05VV- F 2x 0.75 mm2) is connected to terminals marked with the letters L (power line) and N (neutral) mounted on the hood and is secured in position by a cable gland. The mains cable must be connected to a suitable and easily accessible fixed power point. As the electrical installation must comply with the laws and regulations in force only a qualified and authorised electrician must install the hood including connecting it to a double pole switch with a contact gap of at least 3mm.

Connect the mains cable if provided with a plug to a power socket. The user must have access to the power socket to be able to connect and disconnect the plug once the hood is mounted and fixed.

The manufacturer will not be responsible if the gov- erning health and safety laws are not observed which permit safe and correct use of the hood and electrical connections.

Before servicing or repairing the hood make sure the appliance is disconnected from the mains supply either by removing the plug or switching the power socket to OFF.

CLEANING

Clean the outer part of the hood with a soft cloth and liquid detergent, do not use abrasive cleaning prod- ucts or scouring pads.

It is recommended to wash the filters in a dishwash- er or in water up to 60oC every 3 months.

CHANGING THE LIGHT BULB

Before changing the light bulb, ensure that the appli- ance is not live (the switch should be in position 0 - OFF). Remove the metal anti-grease filters (Fig.5). Change the halogen light using a 230V halogen light, with an E14 coupling, max. 50W. Replace the metal anti-grease filters.

WARNINGS

“NOTE: the areas behind the filters are not intended to be cleaned”

Follow the cleaning instructions given by the manu- facturer and in particular take care that there are not grease deposits on the surface of the hood which could create a possible fire hazard. Make sure the electric hob rings or gas rings are always covered when in use to avoid heating the filter.

When frying never leave pans unattended as there is the risk of the oil overheating and catching fire. If reusing frying oil the fire risk is greater. Never pre- pare flame cooked food dishes under the hood. The air duct by the hood must not be conveyed into a flue used for other appliances that run off other energy supplies other than electricity. If the air is to be duct- ed, before installing make sure the flue is in good condition especially if it has been out of use for a long period of time. Always observe governing laws and regulations regarding ducting waste gases. All rec- ommendations given must be scrupulously observed to avoid any possible fire hazard.

2

Page 2 Page 4
Image 3
Page 2 Page 4
Contents An AGA Company Grease Filter Electrical ConnectionElectrical Connection General Guidelines MaintenanceInstallation CleaningFitting Instructions SpecificationsControl Panel VentilationRiveted Brackets Vents Clips to hold Hood Glass Glass in place Dimensions Warranty

Glass Island Hood specifications

The Waterford Precision Cycles Glass Island Hood represents a pinnacle in cycling technology, combining advanced materials with innovative design features to enhance both performance and comfort. As cyclists seek to optimize their riding experience, the Glass Island Hood serves as a standout component in this quest.

One of the standout features of the Glass Island Hood is its lightweight construction. Utilizing cutting-edge materials, this hood significantly reduces overall bike weight without compromising durability. The use of high-strength, lightweight carbon fiber not only decreases weight but also enhances the responsiveness of the bike, allowing for quicker acceleration and better handling.

Another notable characteristic of the Glass Island Hood is its aerodynamic design. Engineers at Waterford Precision Cycles have meticulously crafted the hood to minimize drag while maintaining an aggressive riding position. This sleek profile helps cyclists maintain higher speeds with less energy expenditure, making it ideal for both competitive riders and enthusiasts aiming to improve their overall performance.

Comfort is paramount in long-distance cycling, and the Glass Island Hood excels in this area. The ergonomically shaped hood ensures a natural hand position, reducing stress on the wrists and enhancing grip. Additionally, the integration of vibration-damping technologies helps to absorb road shock, providing a smoother ride over rough terrain. This characteristic allows cyclists to ride longer distances without experiencing discomfort, ultimately making for a more enjoyable cycling experience.

Moreover, the Glass Island Hood boasts a customizable fit, accommodating a range of hand sizes and preferences. With an adjustable design, riders can easily personalize their setup to match their individual needs, ensuring optimal control and comfort.

Waterford Precision Cycles has incorporated advanced technologies into the Glass Island Hood, including smart integration capabilities for accessories. Riders can seamlessly attach lights or other gadgets, enhancing safety and functionality on their rides.

In summary, the Waterford Precision Cycles Glass Island Hood is a transformative cycling accessory that blends lightweight materials, aerodynamic design, and comfort-enhancing technologies. It is expertly crafted for cyclists who demand performance, style, and unparalleled riding experience. As cycling continues to evolve, the Glass Island Hood sets a new standard for what cyclists can expect from their gear.
Top Page Image Contents