Vermont Casting 360DVSL, 360DVS2 Locating Your Fireplace, Please Review the Following Carefully

Page 2

360DVS Series Direct Vent Fireplaces

Installation & Operating Instructions

This gas appliance should be installed by a qualified installer in accordance with local building codes and current CSA-B149.1 Installation Codes for Gas Burning Appliances and Equipment. If the unit is being installed in a mobile home, the installation should comply with the current CAN/CSA Z 240.4 code. For U.S.A. Instal- lations, follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1/NFPA 54.

In the Commonwealth of Massachusetts, all gas fittings and installation of this appliance shall be done by a licensed gas fitter or licensed plumber.

FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE THE FOLLOWING:

1.This fireplace gives off high temperatures and should be located out of high traffic areas and away from furniture and draperies.

2.Children and adults should be alerted to the hazards of high surface temperatures of this fireplace and should stay away to avoid burns or ignition of clothing.

3.CAUTION: Due to high glass surface temperature, chil- dren should be carefully supervised when in the same room as fireplace.

4.Under no circumstances should this fireplace be modified. Parts removed for servicing should be replaced prior to operating this fireplace again.

5.Installation and any repairs to this fireplace must be per- formed by a qualified installer, service agency or gas sup- plier. A professional service person should be contacted to inspect this fireplace annually. Make it a practice to have all of your gas fireplaces checked annually. More frequent cleaning may be required due to excess lint and dust from carpeting, bedding material, etc.

6.Control compartments, burners and air passages in this fireplace should be kept clean and free of dust and lint. Make sure the gas valve and pilot light are turned off be- fore you attempt to clean this fireplace.

7.The venting system (chimney) of this fireplace should be checked at least once a year, and if needed, your venting system should be cleaned.

8.Keep the area around your fireplace clear of combustible materials, gasoline and other flammable vapor and liquids. This fireplace should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or around the fireplace.

9.Under no circumstances should any solid fuels (wood, coal, paper or cardboard, etc.) be used in this fireplace.

10.The flow of combustion and ventilation air must not be obstructed in any way.

11.When the fireplace is installed directly on carpeting, vinyl tile, or any combustible material other than wood, it must be installed on a metal or wood panel extending the full width and depth of the fireplace.

12.This fireplace requires adequate ventilation and combus- tion air to operate properly.

13.This fireplace must not be connected to a chimney flue serving a separate solid fuel-burning fireplace.

14.When the fireplace is not in use, it is recommended the gas valve be left in the “OFF” position.

10006326

This appliance may be installed in an aftermarket, per- manently located, manufactured home, or mobile home where not prohibited by local codes.

This appliance is only for use with type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.

IMPORTANT:

PLEASE REVIEW THE FOLLOWING CAREFULLY

Remove any plastic from trim parts before turning the fireplace ON.

It is normal for fireplaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine.

It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufacturing process.

Please ensure that your room is well ventilated - open all windows.

It is recommended that you burn your fireplace for at least ten (10) hours the first time you use it. If the optional fan kit has been installed, place the fan switch in the “OFF” position during this time.

Proposition 65 Warning: Fuels used in gas, wood- burning or oil fired appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth de- fects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

Locating Your Fireplace

 

 

X

 

 

 

 

X

X

 

 

 

B

 

 

 

A

Y

A

Y

 

 

 

 

Y

Z

 

 

 

 

 

 

 

 

 

LU584-2

Fig. 1

Locating your gas fireplace

 

 

AWall Location (Fig. 1)

Y (Minimum distance between a glass panel and a

parallel wall) = 3’ (914mm)

Z(Minimum distance between edge of a glass panel and an adjacent wall) = 3” (76mm)

B Island Location (Fig. 1)

X (Maximum length of horizontal venting) = 20’ (6.1m)

Refer to the venting section in this manual for specific dimen-

sions.

3

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 360DVSL 360DVSR Locating Your Fireplace Please Review the Following CarefullyTop Vent Configuration Fireplace Dimensions 360DVS2Rear Vent Configuration Fireplace Dimensions 360DVS3 / 306DVSL / 360DVSR Configuration Framing Dimensions 360DVS2Rear Vent Rear Vent Configuration Top Vent ConfigurationRear Vent Configuration Top Vent Configuration Model 360DVS3 Framing Dimensions 360DVS3 / 360DVSL / 360DVSRRear Vent Confiration 360DVSL/RHearth Clearance to CombustiblesMantels Final Finishing Gas Line InstallationFraming & Finishing Gas SpecificationsEB-1 Electrical Junction Box Connection Remote ON/OFF Switch InstallationAlternate Switch Location Alternate switch location Optional Top Vent ApplicationLocation of Vent Termination Electronic Gas Control ValveThere must not be any obstruction such as bushes Canadian Installations US Installations General Venting Information Termination LocationGeneral Information Assembling Vent Pipes Canadian InstallationsUSA Installations Twist Lock PipesRear Wall Application How to Use the Vent GraphRear Wall Installation StepVertical Sidewall Application Locate vent opening on rear wallVertical Side Wall Installation Zero clearance sleeve is required only for combustible wallsAlways install horizontal venting on a level plane Vertical height requirementBelow Grade Installation Horizontal runs if the vertical exceeds 24 610 mmMaximum termination to roof clearance Vertical Through-the-Roof Installation Chimney supportTwist Lock Venting Components Glass Information Window Frame Assembly RemovalFront Window Frame Assembly Louvre RemovalLog Installation Glass CleaningCeramic Refractory Installation Ember Material Pt. #51915 Lava Rock and Ember Material PlacementFlame & Temperature Adjustment Place this lava rock material on burner tilesFlame Characteristics Flame adjustment knob for SIT valveBurner and Burner Compartment Cleaning Standing Pilot Control SystemCleaning Electronic Ignition System Brass Trim360DVS Series 360DVSL 360DVSR 360DVS Series Direct Vent Fireplaces Product Covered by this Warranty If Warranty Service is NEEDED…Efficiency Ratings AFUE%

360DVS3, 360DVSL, 360DVSR, 360DVS2 specifications

Vermont Casting offers a range of high-quality gas stoves designed to enhance home heating and add aesthetic appeal. Among their most popular models are the 360DVSR, 360DVSL, 360DVS2, and 360DVS3. Each of these models features unique characteristics and innovative technologies that set them apart in the world of home heating.

The 360DVSR is a versatile choice known for its superb efficiency and heating capabilities. This model employs advanced technology to ensure optimal performance, featuring a heat exchanger that maximizes heat transfer while minimizing fuel consumption. The DVSR boasts a stunning design with a wide viewing area, allowing users to enjoy the mesmerizing flames. Its easy-to-use electronic ignition ensures that lighting the stove is hassle-free, and it also comes with remote control options for added convenience.

The 360DVSL, on the other hand, is tailored for those seeking a more contemporary aesthetic. This model offers the same outstanding energy efficiency as the DVSR but incorporates a sleek, low-profile design that fits seamlessly with modern interiors. Its programmable thermostat allows users to maintain their desired temperature easily, while the dual-fuel capability enables the use of either natural gas or propane. The 360DVSL is perfect for families looking to combine style with function.

For larger spaces, the 360DVS2 and 360DVS3 are optimal choices. These models are designed with a greater heating capacity, making them suitable for larger rooms or open-concept living spaces. The 360DVS2 features a dual burner system that allows for variable heat output, improving comfort in varying conditions. It also includes a realistic log set that adds to the ambiance of the flame.

Meanwhile, the 360DVS3 distinguishes itself with a three-sided design, offering a panoramic view of the fire from multiple angles. This makes it a stunning focal point in any room. Each model is built with durable materials and features Vermont Casting’s renowned craftsmanship, ensuring longevity and reliability.

In summary, Vermont Casting's range of 360DVSR, 360DVSL, 360DVS2, and 360DVS3 gas stoves combine advanced technology, efficiency, and timeless design. Whether you are looking for versatility, contemporary style, or higher heating capacity, these models offer a solution to meet varied needs while enhancing any living space with the warm ambiance of a gas fire.
Top Page Image Contents