Zanussi ZBG 861 manual Fitting the Appliance and Cabinet, Hinge Stirrup

Page 39

INSTALLATION Flexible Pipe Installation.

FITTING THE APPLIANCE AND CABINET

It is recommend that a 3/8", 1100mm long angled flexible hose (BFS), and a ½ " straight socket (BFS) be used for the installation. However, any approved hose of the right length can be used.

IMPORTANT: Flexible tubing used must comply with BS 669 current editions. L.P.G. flexible connections must be of a type suitable for L.P.G. and capable of operation up to 50mbar and carry a red stripe, band or label.

NOTE: Only liquid sealants can be used in threaded gas connections. Do not use P.T.F.E. tape.

1Make suitable arrangements for gas and electric supplies into the installation site. Preferably a junction box or a 3 pin earthed socket should be situated at the back of the cabinet below the oven.

2The electrical connection to the appliance is at the rear bottom right hand side, the junction box or socket should be positioned accordingly.

3Fit the cabinet as Fig.1, make sure that it is level.

4When unpacking the appliance keep it on its polystyrene base until it is put into the cabinet to avoid damage. Do not allow young children to play with any part of the packaging. After installation, please dispose of the packaging with due regard to the environment, your local authority can arrange this. NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor.

5Open Oven door fully.

6Rotate the hinge stirrups to there forward position see Fig.2.

7To remove the door, clear the hinges by raising the door slightly whilst pulling towards you.

HINGE

STIRRUP

Fig.2

8Remove the gas control knobs, springs, bezels and timer control knobs.

9Remove the four screws (two each side) which are visible on the underside of the fascia. Fig. 3.

10Tilt the bottom of the fascia panel out over. Withdraw the fascia panel by moving it down over to disengage

from the top fixing lugs. Take care not to lose the two rubber grommets from the timer.

NOTE: The thermostat and grill discs will remain attached to the fascia panel. When refitting the control knobs and

bezels, the drive pins on the rear of the bezel must first beFig.3 located in the disc carrier. The knob and spring can now be

fitted onto the control spindle. To prevent the top of the fascia panel mounts becoming slack, it may be necessary to adjust the top fixing lugs.

11If the gas supply bayonet and wall fixing bracket are to

be located behind the appliance it must be located in the shaded area as indicated in Fig.5.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Operatinginstructions For your safety IntroductionG 8 6 Contents Installing the oven For your safety Cabinet DimensionsLocation Cooling fan for the controls General informationIgnition Oven lightPlease note To light Lighting the oven/grillGrill OvenLighting the oven/grill G 8 6 To turn off any burnerHeat control GrillGrill shelf Cooking positionsPreheating Putting food on the gridFor your safety Grill pan is supplied with a removable handle Grill pan and handlePlate warming Heat zones Oven For your safetyOven shelves Baking trays and dishes For your safety RoastingCondensation Put the dishes in the centre of the shelf Oven cooking chartMins. per ½ kg 1 lb and 25 mins Bread 0.45kg 1lb loaves Slow cooking Food preparation slow cookingJoints of meat and poultry Frozen foods G 8 6 Soups, casseroles and stewsVegetables Milk puddingsReheating G 8 6 Milk and milk products, for example creamTo use the countdown Electronic timerElectronic timer To set the time of daySetting the controls for automatic use Electronic timer G 8 6Automatic control To cancel an automatic programme Hints and tips for automatic cooking Care and cleaning For your safety Oven Oven cleaning cycle Cleaning between the outer and inner door glassTo remove the outer glass Rust removers Bath/Sink stain removers Cleaning The Door GlassLCheck What is wrong and why?Problem CheckG 8 6 Problem Replacing an oven light bulb Replacing an oven light bulbService and spare parts For your safety ServiceHelp us to help you Gas Consumers Council Customer care departmentGeneral Technical DataDimensions ConnectionsImportant Safety Requirements OvenProvision for Ventilation 560 Hinge Stirrup Fitting the Appliance and CabinetFixing Points Installation Solid Pipe Installation Connection to Electricity Supply 225Green AMP Blue Pressure Testing RE-ASSEMBLE the ApplianceChecking the Grill Checking the Main Oven Controls Checking the Main OvenAutomatic Operation Standard guarantee conditions Guarantee Conditions

ZBG 861 specifications

The Zanussi ZBG 861 is a versatile built-in oven that combines modern design with advanced cooking technologies, catering to both novice cooks and culinary enthusiasts. This appliance stands out not only for its functionality but also for its sleek and streamlined appearance, seamlessly blending into any contemporary kitchen.

One of the main features of the ZBG 861 is its generous cooking capacity. With a net volume of around 73 liters, it provides ample space to cook multiple dishes simultaneously. This is particularly useful for large families or when entertaining guests. The oven's interior is designed with a smooth enamel coating, making it easy to clean and maintain, which is a significant advantage for busy households.

The ZBG 861 incorporates a variety of cooking functions to accommodate various culinary needs. With options such as traditional baking, grilling, and even steaming, this oven allows users to explore different cooking methods. One standout feature is the fan-assisted cooking function, which ensures even heat distribution throughout the cavity. This technology not only speeds up cooking time but also helps achieve consistent results, whether baking pastries or roasting meats.

Another noteworthy characteristic of the ZBG 861 is its energy efficiency. This oven is designed with a high energy rating, making it an environmentally friendly choice. It operates on less energy without compromising on performance, reflecting Zanussi's commitment to sustainability.

Safety is also a priority in the design of the ZBG 861. The oven is equipped with an advanced cooling fan system that prevents the exterior from overheating, protecting users from burns. Additionally, the oven includes a child lock feature, providing peace of mind for families with young children.

The digital display and intuitive control panel make managing cooking settings straightforward and user-friendly. Users can easily select cooking programs, adjust temperatures, and set timers, ensuring optimal results every time.

In conclusion, the Zanussi ZBG 861 is a reliable and feature-rich built-in oven that enhances kitchen functionality. With its spacious capacity, diverse cooking functions, energy efficiency, and safety features, it is an excellent addition to any modern kitchen, promising delicious results with every meal.
Top Page Image Contents